46 Working At Heights courses

Course Objectives The delegates are able to demonstrate: knowledge of hazards and risks associated with working at heights, specific to WTG (Wind Turbine Generator). understanding of current national legislation regarding working at heights. correct identification of PPE, including identification of European/Global standard markings e.g. harness, hard hat, lanyards, etc. knowledge and skills to correctly inspect, service, store and don the relevant PPE, e.g. harness, lanyards, fall arresters and work positioning equipment. correct use of the relevant PPE, e.g.harness lanyards, fall arresters and work positioning equipment. This includes correct identification of anchor points and correct ladder conduct. correct use of evacuation devices. how to approach rescue situations in WTGs and use rescue equipment efficiently.

This one-day course is a must for all construction operatives! Not only is this a legal requirement under CDM 2015, but if your Company is accredited to CHAS or similar SSIP schemes you must be able to demonstrate that suitable training has been provided to your staff. The Construction Design & Management Regulations 2015 (CDM) sets the requirement for all workers to have the right skills, knowledge, training, and experience. Aims To give a clear understanding of Regulations & Legislation that applies to construction work and is an ideal refresher for any operative that has previously completed training in Health & Safety. Course Content Overview of the following regulations: • The Construction Design & Management Regulations 2015 (CDM) • Health & Safety at Work etc. Act 1974 • Work at Height Regulations 2005. • Control of Asbestos Regulations 2012 • Control of Substances Hazardous to Health Regulations 2002 (CoSHH) • Provision and Use of Work Equipment Regulations 1998 (PUWER) • Personal Protective Equipment at Work Regulations 1992 (PPE) Practical training in: • Abrasive Wheels • CoSHH • Working at Height (awareness) • Manual Handling (awareness). Prerequisites None - The course is intended either as an introduction or as a refresher. Assessment At the end of this course, all delegates will have a clear understanding of the requirements of Health and Safety Legislation and their responsibilities to comply with them. Certificate This course is covered by certification to provide to your Clients, CHAS (and other SSIP) as confirmation of training undertaken and is valid for 3 years. Instructions Cost includes: course notes, certification, lunch & refreshments. Directions Location Map

The delegates are able to demonstrate: The participants are able to demonstrate knowledge of hazards and risks associated with working at height specific to a wind turbine generator (WTG) (L2 – Knowledge) The participants are able to demonstrate understanding of current national and regional legislation regarding working at height (L2 – Knowledge) The participants are able to demonstrate correct identification of PPE, including identification of Global and regional standard markings e.g. harness, hard hat, lanyards, etc. (L3 – Skills) The participants are able to demonstrate the knowledge and skills to correctly perform pre-use inspection, service, store and correctly fit relevant PPE, e.g. harness, fall arrest lanyards, guided type fall arrest lanyards and work positioning lanyards (L2 – Knowledge & L3 – Skills) The participants are able to demonstrate correct use of the relevant PPE, e.g. harnesses fall arrest lanyards, guided type fall arresters and work positioning lanyards. This includes correct identification of anchor points and correct conduct on ladder (L3 – Skills) The participants are able to demonstrate correct use of evacuation devices (L3 – Skills) The participants are able to demonstrate how to approach rescue situations in WTGs and use rescue equipment efficiently (L3 – Skills & Ability)

The aim of this module is to enable delegates to perform entry-type injured person rescue operations, in a Wind Turbine Generator, using industry standard rescue equipment, rescue methods and techniques, exceeding those of GWO Working at Heights. Valid GWO BST Module Working at Heights, GWO First aid and GWO Manual Handling certificates are prerequisites for participation.

Trainer to Candidate Ratio: Working at Height Theory: 12 Students to 1 instructor; Practical: 6 Students to 1 instructor Frist Aid Theory: 12 Students to 1 instructor; Practical: 6 Students to 1 instructor Manual Handling Theory: 12 Students to 1 instructor; Practical: 12 Students to 1 instructor Fire Awareness: Theory: 12 Students to 1 instructor; Practical: 6 Students to 1 instructor Sea Survival: Theory: 12 Students to 1 instructor; Practical: 6 Students to 1 instructor Enhanced First Aid: Theory: 12 Students to 1 instructor; Practical: 6 Students to 1 instructor Advanced Rescue Training: Theory: 12 Students to 1 instructor; Practical: 4 Students to 1 instructor

Highfield Level 1 Award In Health And Safety Within A Construction Environment (RQF) Highfield Level 1 Award in Health and Safety within a Construction Environment (RQF) One day course For those applying for the Green Labourer CSCS Card Includes the Health, Safety, Environment Test For Operatives and Specialists book or DVD by CITB! Face to Face: One day course + time for self-study required This course is supported by the Construction Industry Training Board (CITB) This course is designed to give learners a route to applying for the Green Labourer CSCS Card Course Contents: The purpose of a risk assessment The purpose of a method statement The legal requirements of risk assessments and method statements The common causes of work-related fatalities and injuries The implications of not preventing accidents and ill-health at work Health and safety definitions Hazards and potential risks of a a range of situations The importance of reporting accidents and near misses Accident reporting procedures Risk assessments and dynamic risk assessments The reasons for using safe manual handling in the workplace The employees' responsibilities under current legislation and official guidance in relation to manual handling in the workplace The procedures for safe manual handling Working at height Employees' legal responsibilities in relation to working at height Potential hazards when working at height Controlling risks and hazards while working at height Regulations regarding working at height COSHH: substances hazardous to health Common risks to health within a construction environment Drugs and alcohol Personal Hygiene Asbestos PPE (Personal Protective Equipment) Working around plant and equipment safely Benefits of this course: In 2018/19, 1.4 million people suffered from a work-related illness They have a much higher rate of work-related ill-health than those working in many other industries Construction workers have the highest rate of musculoskeletal disorders compared to other occupations This course develops learners’ knowledge and understanding of health and safety in a construction environment so they can work safely on a construction site Those who successfully complete this Level 1 Award in Health and Safety in a Construction Environment and have completed the CITB Health, Safety & Environment Test within the last 2 years can then apply for a Green Labourer CSCS card. Our Health And Safety In A Construction Environment Training Course is a nationally recognised, Ofqual regulated qualification accredited by Highfields Qualifications. This course leads to the obtainment of the CSCS labour card, allowing workers to work on construction sites. The Ofqual Register number for this course is 603/2442/9

This ESS course is suitable for operatives who during the daily activities have to use Ladders. It will give the delegate an understanding of the safe use and inspection as well as awareness of the regulations. Book via our website @ ESS | Working at Heights training | Vp ESS (vp-ess.com) or via email at: esstrainingsales@vpplc.com or phone on: 0800 000 346

This ESS course is suitable for operatives who during the daily activities have to wear a safety harness. It will give the delegate an understanding of the safe use of a harness, methods of inspection and awareness of the regulations. Book via our website @ ESS | Working at Heights training | Vp ESS (vp-ess.com) or via email at: esstrainingsales@vpplc.com or phone on: 0800 000 346

The Level 1 Award in Construction Health & Safety is required by individuals who are looking to become eligible for the Green CSCS Card. A CSCS Card is required in order to access many construction sites, carry out basic duties and build relevant experience to enable them to progress their career onto the next stage allowing them to progress to a level 2 or 3 Qualification. This Level 1 Award will provide the basic knowledge and understanding of health and safety principles and procedures and delivers a comprehensive and technical overview in relation to many construction relevant topics that are operatives require in order to operate safely within the Construction sector. Topics covered include Risk Assessment, Manual Handling, Working at Heights, Moving Vehicles, Dust, Hazardous Substances, Asbestos, Welfare, Personal Hygiene, Fire, Work Equipment, Electricity, Underground Services, PPE, Mandatory signage and more!!!!! Candidates can undertake this qualification in a classroom based delivery followed by the CSCS test within a single day. The administration and photographs are included and the CSCS card is usually received within 5 to 10 days. The one day course can be delivered in any client venue or at various locations around the UK.

The aim of this module is to enable delegates to support and care for others working in the industry by processing the knowledge, skills and attitude of Enhanced First Aid. Valid GWO BST Module First Aid certificate is a prerequisite for participation.