2823 Courses in Kirkby-in-Ashfield

Chesterfield 2391 Practical Assessments

QA Level 3 Award In Emergency First Aid At Work (RQF) Full day course Gives learners the knowledge and skills to be an emergency first aider Recommended by HSE for low-risk workplaces Course Contents: The Roles and Responsibilities of an Emergency First Aider Assessing an Incident Minor Injuries Cuts, Grazes and Bruises Minor Burns and Scalds Managing an Unresponsive Casualty CPR Safe Use of an AED (Automated External Defibrillator) Choking Seizures Wounds and Bleeding Shock Benefits of this course: 1.1 million workers in Britain had an accident at work in 2014/2015 Of those, 2,700 were from the East Midlands On average, one out of every 370 people received an injury at work The estimated cost of injuries and ill health last year was £15 billion The Health and Safety (First Aid) Regulations 1981 require all employers to make arrangements to ensure their employees receive immediate attention if they are injured or taken ill at work. This includes carrying out a risk assessment, appointing a suitable amount of first aiders and providing adequate first aid training Typically, first aiders will hold a valid certificate in either First Aid at Work (FAW) or Emergency First Aid at Work (EFAW) Our QA Level 3 Award in Emergency First Aid at Work (RQF) - EFAW - training course is the one recommended for first aiders in a low risk workplace Having the correct first aid provision in the workplace is not just a legal requirement, it is incredibly important for the safety of all members of staff! As this is a Regulated Qualification, employers can book this course for their employees in the safe knowledge that they have fulfilled their legal responsibilities for providing quality first aid training, without having to undertake any lengthy due diligence checks Accredited, Ofqual regulated qualification: Our Emergency First Aid at Work course is a nationally recognised, Ofqual regulated qualification accredited by Qualsafe Awards. This means that you can be rest assured that your Emergency First Aid at Work Certificate fulfills the legal requirements and is a very good way to make sure you and your employees are trained in First Aid. The Ofqual Register number for this course is 603/2367/X

QA Level 3 Award In First Aid At Work (Annual Refresher) (RQF) Half day course How much do you still remember from your last first aid training course? Skills fade rapidly. This course is there to ensure learners retain the most important skills of saving a life. The Annual Refresher as recommended by HSE Course Contents: Assessing an Incident Managing an Unresponsive Casualty Recovery Position CPR Safe Use of an AED (Automated External Defibrillator) Choking Benefits of this course: 1.1 million workers in Britain had an accident at work in 2014/2015 Of those, 2,700 were from the East Midlands On average, one out of every 370 people received an injury at work Are you already holding a valid Emergency First Aid at Work (EFAW) or First Aid at Work (FAW) Certificate? How much can you still remember a year later? HSE strongly recommends that first aiders undertake Annual Refresher training during any three year FAW/EFAW certification period. This will help qualified first aiders remain competent and keep up to date with any changes to first aid procedures. In just half a day, this course is an ideal way to satisfy HSE requirements whilst minimising disruption to the work day. Accredited, Ofqual regulated qualification: Our Emergency First Aid at Work Annual Refresher course is a nationally recognised, Ofqual regulated qualification accredited by Qualsafe Awards.This means that you can be rest assured that your Emergency First Aid at Work Annual Refresher Certificate fulfils the legal requirements and is a very good way to make sure you and your employees keep your First Aid skills up to date.The Ofqual Register number for this course is 603/3154/9

One and a half-hour session Have you already got a valid First Aid Certificate? Do you feel confident you can do what needs to be done when the situation arises? Are there first aid situations you do not feel ready for, that were maybe not covered or are now more important to you? These special First Aid Skills Practice Sessions give you the chance to refresh your theory and/or practical skills Whichever subjects you would like to work on - you choose what you want to practice or know more about Course Contents: Can’t quite remember how or why to put someone in the recovery position? Practice it! Still confident in giving CPR? Ever done it with different barriers? Here’s your chance. Scared of what to do if someone chokes? We have baby and child infant choking models and an adult choking vest. Save their lives! Bandage a wound, apply a sling, treat someone for shock? That can be done. Want to know more about Heart Attacks or Strokes? Just let us know. Know the theory about an Automated External Defibrillator (AED), but haven’t had the chance to actually use one? Now you can. And so on and so forth – the choice is yours! Benefits of this course: Have you already got a valid First Aid Certificate? Can you still remember everything that you have learned? Or maybe you did some training a while ago that wasn't necessarily certificated, and you just want to refresh your skills and knowledge a bit Do you feel confident you can do what needs doing when the situation arises? It is highly recommended to do 'something’ to keep your skills up to date – as a matter of fact, this is a prerequisite of your First Aid Certificate. We run Annual Refresher courses, which is a properly accredited certification awarded by Qualsafe Awards. These are recommended on a yearly basis. In between that, it is still good to keep one's skills and knowledge up to date. Our special First Aid Skills Practice Sessions give you the chance to refresh your theory and/or practical skills. Whichever subjects you would like to work on. An experienced trainer will be at hand to show and explain. NOWHERE ELSE DO YOU HAVE THE CHANCE TO DO THIS! CPD Accredited: These sessions are non-Ofqual regulated. However, they are taught by our trainer, who is an accredited first aid trainer via Qualsafe Awards, First Aid Awards Ltd and Highfields Qualifications. You'll get accredited quality either way! These sessions are CPD Accredited, so you'll get 1.5 CPD hours with this training. If you'd like to do a nationally accredited course instead, we'd like to recommend you do our First Aid at Work Annual Refresher, Emergency First Aid at Work, First Aid at Work or Basic Life Support for Adults and Children course.

Course Summary Taught by Sports Massage Therapist Laura Simmons, this practical course will cover everything you need to know, enabling you to incorporate Dry Suction Cupping into your current treatments. Covering all the theory as well as ensuring you have plenty of practical demonstration and practice during the course. This is a great addition to any manual therapist treatment for both the therapist and the patient. You will be introduced to the use of Dry Cupping therapy for the purpose of muscular pain relief via a blend of theory and practical components. With a substantial amount of practical work where you will gain adequate practice to hone your skills enabling you to use all the techniques shown within your practice. Course Content Introduction History of Cupping Different Cups Cupping Application Effects of Cupping Contractions & Contraindications Effects of Cupping Gathering Information Cupping Application; Massage, Stationary, Pin and Stretch and Active Cupping We only have small numbers on all our courses ensuring you have plenty of time with Laura to really develop your technique and feel confident in offering this technique to your patients. We pride ourselves on always being there ready to help and offer advise not only during the course but after as well, all you need to do is ask! Course Prerequisites Physiotherapists Osteopaths Chiropractors Manual Therapists Sports Therapists Sports Massage Therapists Personal trainers We may ask you to provide a copy of your qualification. Assessment Observation during the course day Once completed you will be able to add Dry Cupping therapy on to your own indemnity insurance Venue BTST Academy & Clinic, Holly Farm, Clipstone Road, Edwinstowe, Nottingham, NG21 9JD Course Times 9:30am – 4:30pm Course Price £ 175 Course Terms & Conditions: Course payment is non refundable , Click here for the terms and conditions. Course Accreditation Accredited by Active IQ

What is the AM2 assessment? The AM2 assessment is an industry recognised trade test designed to evidence that candidates have gained all relevant and safety-critical competencies during their training process. It provides a single standard that has been agreed upon by employers within the electrical industry, giving a reliable and trusted guarantee of safe, high-quality skills for the electrotechnical industry. Who is this for? This is aimed at apprentices who are coming to the end of their training for the JIB apprentice training scheme and the Installation of modern apprenticeships. This course is also for experienced electricians, specifically those who are looking at taking the experienced worker route (AM2E.) There are a range of assessments for candidates based on their level: AM2 – This is for candidates undertaking the JIB mature candidate assessments and those following the level three NVQ who isn’t an apprentice. AM2S – This is for electrotechnical apprentices who are training against the apprenticeship standard AM2E – This is for experienced workers who are completing the experienced worker assessment. Please note: this can only be taken once you have gained the experienced worker qualification, proof must be provided before booking the AM2 assessment. What does this assessment consist of? Overall, the AM2 is an in-depth assessment carrying out tasks to show what you have learnt on your training. It is a practical assessment with five sections (six for AM2E and AM2S) and a short online component. Candidates will be expected to install, connect, terminate, inspect, test, commission and diagnose faults, following installation specifications provided and any relevant statutory and non-statutory regulations on: A three-phase distribution board and subcircuit A central heating/sustainable energy system Lighting and power circuits A data cabling system A safety services circuit and device Installation of containment systems (AM2E and AM2S only) Candidates will complete timed tasks in equipped areas that contain typical electrical installation wiring systems – all work must comply with BS7671 Wiring Regulations, industry best practice, and meet the requirements of relevant health and safety legislation. The assessment will be carried out in strict exam conditions across 2.5 days. Do I need an AM2 certificate to work as an electrician? Apprentices must pass their AM2 test in their final year to complete their apprenticeship. Also, if the apprenticeship standard is not being followed, an AM2 certificate and a level three NVQ is required to gain a gold card. If you are already working as an electrician, you will not need an AM2 certificate. If you are training to be an electrician and are registering for your NVQ level three in Electrical Installation or Maintenance, the electrotechnical diploma now includes the AM2. The AM2 certification is an industry recognised and something that many employers will actively seek when hiring new staff. It can also be attractive to potential customers.

Our intensive 10, 15 or 20 day Total Air Conditioning and Refrigeration training courses have been structured to meet the ever increasing demands on industry to meet safety, environmental and legal requirements regarding installation, commissioning, service and maintenance of both refrigeration and air conditioning systems including the electrical aspects of installation dependent upon course selection. The first 10 days of the Total Air Conditioning and Refrigeration training course are mechanical only, the following 5 or 10 days are the electrical aspects, depending on which route you need to go down. The Total Air Conditioning and Refrigeration training courses are accredited with the City & Guilds 2079, BESA Pipework and Brazing – (commercial), along with an EAL Unit* – Maintenance of Refrigeration Systems from the EAL Certificate in Engineering Technology (QCF) qualification. (*Practical elements will be covered during the course with a Project booklet to be completed by the student with an element of self-study after the course completion for us to claim the Unit certification from EAL). Our Total Air Conditioning and Refrigeration training courses are designed to be as practical as they possibly can be, with workshop time taking more than 70% of the course. During the Total Air Conditioning and Refrigeration training course, you will, install, repair, fault find, adapt and commission on a variety of different equipment, because we believe the way to learn is to do it!! With ALL our courses we offer unbiased technical support and access to a wealth of knowledge and information upon completion. Once you’ve completed your course with Technique, you can be assured that our service doesn’t end there…

Our intensive 10, 15 or 20 day Total Air Conditioning and Refrigeration training courses have been structured to meet the ever increasing demands on industry to meet safety, environmental and legal requirements regarding installation, commissioning, service and maintenance of both refrigeration and air conditioning systems including the electrical aspects of installation dependent upon course selection. The first 10 days of the Total Air Conditioning and Refrigeration training course are mechanical only, the following 5 or 10 days are the electrical aspects, depending on which route you need to go down. The Total Air Conditioning and Refrigeration training courses are accredited with the City & Guilds 2079, BESA Pipework and Brazing – (commercial), along with an EAL Unit* – Maintenance of Refrigeration Systems from the EAL Certificate in Engineering Technology (QCF) qualification. (*Practical elements will be covered during the course with a Project booklet to be completed by the student with an element of self-study after the course completion for us to claim the Unit certification from EAL). Our Total Air Conditioning and Refrigeration training courses are designed to be as practical as they possibly can be, with workshop time taking more than 70% of the course. During the Total Air Conditioning and Refrigeration training course, you will, install, repair, fault find, adapt and commission on a variety of different equipment, because we believe the way to learn is to do it!! With ALL our courses we offer unbiased technical support and access to a wealth of knowledge and information upon completion. Once you’ve completed your course with Technique, you can be assured that our service doesn’t end there…

Course Description: The 18th edition course is a 3 day short course aimed at anyone involved in the design, construction and inspection and testing of electrical systems, also a nationally recognised ‘must have’ qualification for companies seeking to recruit electricians. It is intended to introduce the candidate to a working knowledge of the Wiring Regulations along with a brief overview of the Electricity at Work Regulations covering their statutory duties. Previous knowledge of the regulations is not assumed, however, a fundamental knowledge of electrical principles is assumed. Please be aware that the Wiring Regulations course is not designed to teach you every regulation in the book but it will teach you the best practices on how the reference the latest regulations as you would on the job. As such key topics currently covered on the 17th Edition will still be included. We have been delivering Wiring Regulations courses for many years and although it is mainly theory based you cannot beat real training in a real classroom. By training with other people in your class you will benefit from being able to ask relevant questions as well as finding the answers to many questions from your fellow students that you may not have even thought of. The examination is a 2 hour multiple choice, open book PC based examination with instant results. The course cost includes examination entry fees. Focus: You will study the latest standard of the IET wiring regulations, including essential subjects such as safety, selection and erection of electrical equipment. There are 8 key modules and current amendments: Section 1 – Scope, Object and FundamentalsSection 2 – DefinitionsSection 3 – Assessment of general characteristicsSection 4 – Protection for SafetySection 5 – Selection and Erection of equipmentSection 6 – Inspection & TestingSection 7 – Special Installations or locationsSection 8 – Functional Requirements This course does include the latest amendments such as: Electromagnetic Disturbance Surge Protection Medical locations Operating and Maintenance Gangways Arc Fault Detection Devices (AFDDs) Changes to fire safety requirements in chapter 422, covering the design of electrical installations in industrial, commercial and multiple-occupancy homes, as well as new information for ‘protected escape routes’ Protection against over voltages Changes across Part 7: Special Locations This classroom based course will show, teach and perfect you on how to reference and use the book for situations that you will encounter while working in the field.

Day 1 Solenoids and actuators, principles of operation and maintenance State precautions that may be necessary when removing cores from energised AC solenoids Transformers, sizing, applications and uses Heaters, applications, uses and safety precautions to be observed Temperature controllers, various types, principles of operation and uses Thermal sensors, various types, principles of operation and uses. Day 2 Proximity devices, limit switches and proximity switches, various types, principles of operation and uses Practical workshop, gaining an understanding of typical connections of various proximity devices and the range of available supplies catered for, voltage levels and current type Development of a typical simple control system using push buttons, proximity devices, relays and indicator lamps. Day 3 Protection against overcurrent Protective devices, various types, suitability and uses Earthing, including principles of protection against indirect shock Undervoltage protection. Day 4 Cable and core termination techniques, including crimping and soldering Practical workshop terminating YY, SY, SWA and MICC cable Testing, basic principles of circuit protective conductor testing and insulation resistance testing, instruments used and expected values Practical workshop testing cables terminated previously and testing cables with faults on test rig. Day 5 Fault finding, safety precautions and principles Practical workshop on fault rigs Root cause analysis PPM and maximising uptime