Maintenance courses

This qualification aims to provide expert guidance to learners wishing to gain knowledge and understanding on Electric Vehicle charging equipment installation. This 2 day course provides expert guidance on EV charging equipment installation, an important emerging area which is not covered in detail by the current edition of the Wiring Regulations (BS 7671) or the IET’s Guidance Notes. Aimed at experienced electricians interested in understanding a wide range of equipment and systems available, this course applies to the specialised installation requirements of electric vehicle charging equipment in domestic dwellings, on-street locations, commercial and industrial premises. The course provides detailed guidance and recommendations on all aspects of the installation of Electric Vehicle Charging Equipment from the origin of the electrical supply, through distribution and final circuits, installation of the charging equipment itself to the cable between the charging equipment and vehicle’s electrical inlet. Also included are related issues of site layout and planning and subsequent inspection, testing, certification and maintenance of installations. Why take this course? Currently there is an increasing demand for new electric vehicle charging points but too few installers to roll them out. This is already a booming market which is due to get much bigger in the near future. The number of public charging connectors and locations has increased by 38% in the past 12 months and is expected to continue at that rate for years to come. Entry Requirements There are no formal entry requirements for this qualification, however we do expect you to meet the following requirements: Minimum age 18 years old (mandatory) Must be able to demonstrate the following competencies Be able to correctly install and terminate: pvc/pvc cable (twin and earth) Steel Wire armoured cable (swa) Be able to carry out an initial verification (inspection & testing) on an electrical installation and complete the necessary paperwork. Please Note: These competencies are required for the assessment and are not taught as part of the course. It is also recommended that you are up to date with your wiring regulations.

This EV charging course is intended to provide expert guidance to learners wishing to gain knowledge and understanding on Electric Vehicle charging equipment installation. This 2 day course provides expert guidance on EV charging equipment installation, an important emerging area which is not covered in detail by the current edition of the Wiring Regulations (BS 7671) or the IET’s Guidance Notes. Aimed at experienced electricians interested in understanding a wide range of equipment and systems available, this course applies to the specialised installation requirements of electric vehicle charging equipment in domestic dwellings, on-street locations, commercial and industrial premises. This training course provides detailed guidance and recommendations on all aspects of the installation of Electric Vehicle Charging Equipment from the origin of the electrical supply, through distribution and final circuits, installation of the charging equipment itself to the cable between the charging equipment and vehicle’s electrical inlet. Also included are related issues of site layout and planning and subsequent inspection, testing, certification and maintenance of installations. Also Covering: How EV charging works How to select the correct EV Charging Point Solution for the customers needs. Technical requirements of installing & the use of different earthing arrangements (TN-C-S/TT systems) Planning requirements, labelling & risk assessments How to carry out surveys & Pre Installation considerations Meeting the requirements of BS7671 Awareness of the IET code of practice for Electrical Vehicle Charging Equipment & Installation. Plus much more Why take this EV charging course? Currently there is an increasing demand for new electric vehicle charging points but too few installers to roll them out. This is already a booming market which is due to get much bigger in the near future. The number of public charging connectors and locations has increased by 38% in the past 12 months and is expected to continue at that rate for years to come. Add this important service to future proof your knowledge to allow extra inspection & testing plus new installation work with this electric vehicle charging course. We have a variety of charging units and simulated installs which means it is just as working on a real installation. Making this installers course real value for money.

Learn how to cannulate ... Nationally Recognised Qualification OCN Accredited - Level 3 (advanced) - Ireland Level 5 CPD Accredited - The CPD Certification Service Classroom or Virtual Classroom options Covers all steps for cannulating in arm or hand Practise on artificial arms and fake blood! Essential qualification for all IV therapies Phlebotomy training desirable but not essential Basic understanding of English language required OPEN TO ALL APPLICANTS

Day 1 of the Industrial Electrical Maintenance Part 1 consists of: Electricity at Work Regulations 1989, requirements and implementation Working safely, including the importance of isolation procedures and lock out systems Switches and Push Buttons, an explanation of the various types of switches and push buttons, the terminology and electrical symbols which are used in industry today, along with practical testing of functionality Relays and Contactors, principles of operation, purpose and uses Circuit design using BS electrical symbols and ladder diagrams, simple retaining circuits Construction of the above circuit, demonstrating the techniques of cable termination. Day 2 of the Industrial Electrical Maintenance Part 1 consists of: 3 phase induction motors, synchronous and asynchronous Description of the component parts of a 3 phase induction motor Demonstration of how a 3 phase rotating magnetic field is produced and how to reverse it Explanation of synchronous and asynchronous speed and slip Effect of the number of poles on motor speed Frame sizes Practical identification of various motors. Day 3 of the Industrial Electrical Maintenance Part 1 consists of: Principles of 3 phase induction motor control systems Overload protection principles of operation and use Design and operation of a DOL (direct on line) starter Construction of a DOL starter Inspection and testing procedure for the above starter Motor testing procedures. Day 4 of the Industrial Electrical Maintenance Part 1 consists of: DOL starter modifications Importance of updating documentation Design, construction and verification of reversing starter control and power circuits. Day 5 of the Industrial Electrical Maintenance Part 1 consists of: Star delta starters, principles of operation and uses Design, construction and verification of star delta starter control and power circuits.

This industrial electrical maintenance course is designed to enable candidates who have a small amount of electrical knowledge to gain recognised qualifications and skills to enable them to enter an industrial environment and work as a industrial electrician. The industrial electrical maintenance course will include a large amount of practical, enabling the candidate to install, fault find, design and wiring up control panels, using a variety of different methods. Industrial electrical maintenance course Aims The aim of the industrial electrical maintenance course is to provide solid foundations upon which the participant will be able to build and develop. Emphasis is given to providing the necessary skills, which will allow the participant to carry out routine electrical tasks. It is also made clear that a participant needs to identify and know their own limitations, allowing tasks to be carried out in a safe manner, not giving rise to danger.

This industrial electrical maintenance course is designed to enable candidates who have a small amount of electrical knowledge to gain recognised qualifications and skills to enable them to enter an industrial environment and work as a industrial electrician. The industrial electrical maintenance course will include a large amount of practical, enabling the candidate to install, fault find, design and wiring up control panels, using a variety of different methods.

This industrial electrical maintenance course is designed to enable candidates who have a small amount of electrical knowledge to gain recognised qualifications and skills to enable them to enter an industrial environment and work as a industrial electrician. The industrial electrical maintenance course will include a large amount of practical, enabling the candidate to install, fault find, design and wiring up control panels, using a variety of different methods.

This industrial electrical maintenance course is designed to enable candidates who have a small amount of electrical knowledge to gain recognised qualifications and skills to enable them to enter an industrial environment and work as a industrial electrician. The industrial electrical maintenance course will include a large amount of practical, enabling the candidate to install, fault find, design and wiring up control panels, using a variety of different methods.

This City & Guilds one day training course will allow service engineers to meet the industry standards requirements for service and maintenance of refrigeration systems containing flammable refrigerants (A3 & A2L) including R290 and R600a. It will provide you with the skills and knowledge to safely handle hydrocarbon refrigerants during installation, service, maintenance and disposal. It is also suitable for engineers working with flammable HFO’s and HFC’s including R1234yf, R1234ze and R32. On successful completion of the course, candidates will be proficient in handling flammable refrigerants contained within refrigeration, air conditioning and heat pump systems and; Dangers of working with hydrocarbons and identifying hazards Regulations for the installation, servicing and de-commissioning of hydrocarbon RAC systems Create a safe working environment and to be able to handle refrigerants safely including recovery, storage and transportation of recovered refrigerants Be able to dispose of recovered refrigerants and oil correctly

This is a full 4 day course covering the requirements of commercial fire alarm systems to BS 5839 Part 1 2017 Code of Practice for Design, Installation, Commissioning and Maintenance of Systems in Non-Domestic Premises. This is one of the few externally examined Level 3 courses available and is supported by the Fire Industry Association (FIA) and Independent Fire Engineering & Distributors Association (IFEDA). All successful delegates will receive a EAL Level 3 Award in the Requirements of Fire Detection and Fire Alarm Systems for Buildings BS 5839-1:2017