Installation courses in Sheffield

What is the AM2 assessment? The AM2 assessment is an industry recognised trade test designed to evidence that candidates have gained all relevant and safety-critical competencies during their training process. It provides a single standard that has been agreed upon by employers within the electrical industry, giving a reliable and trusted guarantee of safe, high-quality skills for the electrotechnical industry. Who is this for? This is aimed at apprentices who are coming to the end of their training for the JIB apprentice training scheme and the Installation of modern apprenticeships. This course is also for experienced electricians, specifically those who are looking at taking the experienced worker route (AM2E.) There are a range of assessments for candidates based on their level: AM2 – This is for candidates undertaking the JIB mature candidate assessments and those following the level three NVQ who isn’t an apprentice. AM2S – This is for electrotechnical apprentices who are training against the apprenticeship standard AM2E – This is for experienced workers who are completing the experienced worker assessment. Please note: this can only be taken once you have gained the experienced worker qualification, proof must be provided before booking the AM2 assessment. What does this assessment consist of? Overall, the AM2 is an in-depth assessment carrying out tasks to show what you have learnt on your training. It is a practical assessment with five sections (six for AM2E and AM2S) and a short online component. Candidates will be expected to install, connect, terminate, inspect, test, commission and diagnose faults, following installation specifications provided and any relevant statutory and non-statutory regulations on: A three-phase distribution board and subcircuit A central heating/sustainable energy system Lighting and power circuits A data cabling system A safety services circuit and device Installation of containment systems (AM2E and AM2S only) Candidates will complete timed tasks in equipped areas that contain typical electrical installation wiring systems – all work must comply with BS7671 Wiring Regulations, industry best practice, and meet the requirements of relevant health and safety legislation. The assessment will be carried out in strict exam conditions across 2.5 days. Do I need an AM2 certificate to work as an electrician? Apprentices must pass their AM2 test in their final year to complete their apprenticeship. Also, if the apprenticeship standard is not being followed, an AM2 certificate and a level three NVQ is required to gain a gold card. If you are already working as an electrician, you will not need an AM2 certificate. If you are training to be an electrician and are registering for your NVQ level three in Electrical Installation or Maintenance, the electrotechnical diploma now includes the AM2. The AM2 certification is an industry recognised and something that many employers will actively seek when hiring new staff. It can also be attractive to potential customers.

A ½ day short City and Guilds 2393-10 course aimed at anyone involved in electrical installations in dwellings. The Government approved Document P (electrical safety) came into effect on the 1st January 2005. For the first time the mainstream work of domestic electrical installers became subject to the requirements and procedures associated with Building Control. Domestic Electrical installers need to appreciate the requirements that apply to building work they carry out in connection with their electrical work, and they need to understand the way that Building Control works and the procedures that need to be followed. This short City and Guilds 2393-10 course is to enable those involved in the installation of electrical systems within the domestic environment to gain an understanding of how electrical installations in dwellings must comply with all relevant Building Regulations and how electrical installations in dwellings can affect the building construction. Please note that this City and Guilds 2393-10 qualification is only suitable for those practising their trade in England and Wales due to their being different regulations in Scotland and Northern Ireland. The City and Guilds 2393-10 examination is a 40 minute open book pc based assessment and will be held in the afternoon following the course, with instant results. The City and Guilds 2393-10 course costs include examination entry fees.

This qualification aims to provide expert guidance to learners wishing to gain knowledge and understanding on Electric Vehicle charging equipment installation. This 2 day course provides expert guidance on EV charging equipment installation, an important emerging area which is not covered in detail by the current edition of the Wiring Regulations (BS 7671) or the IET’s Guidance Notes. Aimed at experienced electricians interested in understanding a wide range of equipment and systems available, this course applies to the specialised installation requirements of electric vehicle charging equipment in domestic dwellings, on-street locations, commercial and industrial premises. The course provides detailed guidance and recommendations on all aspects of the installation of Electric Vehicle Charging Equipment from the origin of the electrical supply, through distribution and final circuits, installation of the charging equipment itself to the cable between the charging equipment and vehicle’s electrical inlet. Also included are related issues of site layout and planning and subsequent inspection, testing, certification and maintenance of installations. Why take this course? Currently there is an increasing demand for new electric vehicle charging points but too few installers to roll them out. This is already a booming market which is due to get much bigger in the near future. The number of public charging connectors and locations has increased by 38% in the past 12 months and is expected to continue at that rate for years to come. Entry Requirements There are no formal entry requirements for this qualification, however we do expect you to meet the following requirements: Minimum age 18 years old (mandatory) Must be able to demonstrate the following competencies Be able to correctly install and terminate: pvc/pvc cable (twin and earth) Steel Wire armoured cable (swa) Be able to carry out an initial verification (inspection & testing) on an electrical installation and complete the necessary paperwork. Please Note: These competencies are required for the assessment and are not taught as part of the course. It is also recommended that you are up to date with your wiring regulations.

Learners will develop knowledge from the FD&FA foundation courses (C01 modules 1 and 2) and/or industry experience with specific regard to more complex system design considerations.

This EV charging course is intended to provide expert guidance to learners wishing to gain knowledge and understanding on Electric Vehicle charging equipment installation. This 2 day course provides expert guidance on EV charging equipment installation, an important emerging area which is not covered in detail by the current edition of the Wiring Regulations (BS 7671) or the IET’s Guidance Notes. Aimed at experienced electricians interested in understanding a wide range of equipment and systems available, this course applies to the specialised installation requirements of electric vehicle charging equipment in domestic dwellings, on-street locations, commercial and industrial premises. This training course provides detailed guidance and recommendations on all aspects of the installation of Electric Vehicle Charging Equipment from the origin of the electrical supply, through distribution and final circuits, installation of the charging equipment itself to the cable between the charging equipment and vehicle’s electrical inlet. Also included are related issues of site layout and planning and subsequent inspection, testing, certification and maintenance of installations. Also Covering: How EV charging works How to select the correct EV Charging Point Solution for the customers needs. Technical requirements of installing & the use of different earthing arrangements (TN-C-S/TT systems) Planning requirements, labelling & risk assessments How to carry out surveys & Pre Installation considerations Meeting the requirements of BS7671 Awareness of the IET code of practice for Electrical Vehicle Charging Equipment & Installation. Plus much more Why take this EV charging course? Currently there is an increasing demand for new electric vehicle charging points but too few installers to roll them out. This is already a booming market which is due to get much bigger in the near future. The number of public charging connectors and locations has increased by 38% in the past 12 months and is expected to continue at that rate for years to come. Add this important service to future proof your knowledge to allow extra inspection & testing plus new installation work with this electric vehicle charging course. We have a variety of charging units and simulated installs which means it is just as working on a real installation. Making this installers course real value for money.

This City & Guilds one day training course will allow service engineers to meet the industry standards requirements for service and maintenance of refrigeration systems containing flammable refrigerants (A3 & A2L) including R290 and R600a. It will provide you with the skills and knowledge to safely handle hydrocarbon refrigerants during installation, service, maintenance and disposal. It is also suitable for engineers working with flammable HFO’s and HFC’s including R1234yf, R1234ze and R32. On successful completion of the course, candidates will be proficient in handling flammable refrigerants contained within refrigeration, air conditioning and heat pump systems and; Dangers of working with hydrocarbons and identifying hazards Regulations for the installation, servicing and de-commissioning of hydrocarbon RAC systems Create a safe working environment and to be able to handle refrigerants safely including recovery, storage and transportation of recovered refrigerants Be able to dispose of recovered refrigerants and oil correctly

This is a gateway course for all further learning in FD&FA systems.

Learners will develop knowledge from the FD&FA foundation BS 5839-1 module and/or industry experience and apply this to the installation of FD&FA systems.

The RQF examination allows learners to demonstrate knowledge of BS 5839-1: 2017 as part of competence in the design, installation, commissioning, and maintenance of FD&FA systems.

The Alarm Installation Course is designed to teach participants how to install an intruder alarm system in domestic, commercial or industrial premises. The Alarm Installation Course simulates the practical installation of many different alarm control panels. The course is designed to equip students with the skills and expertise to competently install a wide variety of Alarm systems on the market.