• Professional Development
  • Medicine & Nursing
  • Arts & Crafts
  • Health & Wellbeing
  • Personal Development

63 Educators providing Courses in Sheffield

123...7

Courses matching "form"

Show all 509

C&G 2391-52, Initial and Periodic Inspection and Testing of Electrical Installations

4.7(1243)

By Technique Learning Solutions

City & Guilds 2391-52 Combined Course: Course Description The new Testing and Inspection City & Guilds 2391-52 Combined Course qualification replaces and is improved on the former 2394/2395 that was previously available to electricians but has since been withdrawn. City & Guilds 2391-52 course runs over five consecutive days, the first three days covering fundamental theory. The fourth day covering Initial Verification practical and revision. The fifth day of the City & Guilds 2391-52 course covering Periodic Inspection practical and revision with an open book 2 hours Multiple choice exam. A 5 day City & Guilds 2391-52 course for a student possessing knowledge of the wiring regulations and with minimal knowledge of inspection and testing, We strongly recommend City and Guilds 2382 is achieved prior to sitting this course, though this is NOT an entry requirement. In order to claim the full City & Guilds 2391-52 qualification, students must successfully complete the following: Completed during the course each student will sit a 2 hours online Multiple choice exam (open book) Then will have to reattend and complete a Practical Assessment which is 4hrs. Assessment – 2391-52 Task A – Visual Inspection – 30mins Task B – Periodic Inspection and Test – 2hrs and 30mins Task C – Short Answer Questions – 1hr and 20mins To further support this course, we offer a 1 day practical workshop (at the cost of £120.00 Net VAT) available to candidates who have completed the course and require further ‘hands on’ practical experience prior to their practical exam. Most students who take this option elect to complete this the day before their practical assessment. The City & Guilds 2391-52 course costs include examination entry fees. The Tutors: Our Tutors are qualified, highly experienced, enthusiastic, knowledgeable and extremely friendly, you can take full advantage of all the tips of the trade, personal experiences and practical advice they offer. This short theory course is intensive, but no compromise is made on the course content. The atmosphere is relaxed and enjoyable which creates a good learning environment. On-site Available Group Rate: (up to 8 people): £895.00 + VAT Per Day* plus £50.00 + VAT Exam Entry Fee per Student *(over 8 people, please call on 0800 112 3310 to discuss Group Rate) This course replaces City & Guilds 2394/2395 combined – Level 3. Essential Book supplied *throughout* course!First exam fee included!

C&G 2391-52, Initial and Periodic Inspection and Testing of Electrical Installations
Delivered in Clay Cross + 1 more or Online + more
£120

Conflict Management 1 Day Training in Sheffield

By Mangates

Conflict Management 1 Day Training in Sheffield

Conflict Management 1 Day Training in Sheffield
Delivered In-Person + more
£595 to £795

The Ultimate Guide to Event Planning - 1 Day Workshop in Sheffield

By Mangates

Event Planning 1 Day Training in Sheffield

The Ultimate Guide to Event Planning - 1 Day Workshop in Sheffield
Delivered In-Person + more
£595 to £795

EICR Form Filling Course

4.7(1243)

By Technique Learning Solutions

Our course is designed by industry experts who know the challenges you face and the skills you need to overcome them. Here’s what you can expect: Clarity and Confidence: Get a clear understanding of every section of the EICR form and learn exactly what each field requires. No more confusion or hesitation. Compliance Made Easy: Stay up-to-date with the latest regulations and standards, ensuring every form you complete is compliant and ready for approval. Time-Saving Techniques: Discover tips for quickly gathering and organizing information so that filling out forms becomes a seamless part of your inspection routine. Practical Exercises: With real-life examples and guided exercises, you’ll learn to navigate common issues and avoid mistakes that can lead to delays or additional work.

EICR Form Filling Course
Delivered In-Person in Clay Cross
£500

C&G 2377-77 – 2 Day

4.7(1243)

By Technique Learning Solutions

Learn how to test portable electrical appliances with a qualification in Electrical Equipment Maintenance and Testing. Aimed at practicing electricians this qualification will help and progress individuals within the Electrotechnical industry. This qualification is aimed at those with responsibilities for the maintenance of electrical equipment and for those undertaking practical inspection and testing of electrical equipment. It allows those with the responsibility for the testing and inspection of electrical equipment to gain a qualification suitable to their job role. The qualification allows candidates to learn, develop and practise the skills required to inspect and test items of electrical equipment in line with the latest edition of the Code of Practice for In-Service Inspection and Testing of Electrical Equipment. If you already work as an electrician it will add another string to your bow and can help you move up in the industry. Learners completing the qualification will have the ability to carry out mandatory responsibilities within the workplace depending on their prior electrical knowledge This level will suit you if you are a practising electrician either involved in, or looking to become involved in, the inspection and testing of electrical equipment. To successfully complete the qualification learners will have to sit an Evolve on-line test comprising of a 50 MCQ and a practical assignment. The practical consists of 3 tasks which are: Task 1 is inspect and test Class I equipment, Task 2 is inspect and test Class II equipment (this will be either unearthed metal or without unearthed metal or Class II FE – Learners will not need to do all 3 of these, they only need to do one type), Task 3 is completing the record forms

C&G 2377-77 – 2 Day
Delivered in Scotland + 1 more or Online + more
£500

Principles of COSHH

5.0(50)

By Pochat Training

QA Level 2 Award In Principles Of COSHH (RQF) Face to Face: Half-day course Virtual Classroom: Spread over 2 sessions of 2½ hr duration COSHH: Control of Substances Hazardous to Health Regulations 2002 Hazardous substances are everywhere, and COSHH assessments have to be undertaken in all businesses Run in an engaging and interactive way - see the video below Course Contents: Legal requirements relating to hazardous substances in the workplace Employer duties Employee duties Consequences of non-compliance Communicating safety information The different forms that hazardous substances can take Effects that may arise after exposure to hazardous substances The different routes that hazardous substances can enter the body How risk assessments reduce accidents and ill health at work The five step process of risk assessment The control hierarchy in relation to the safe use, handling, transporting, storage and disposal of substances hazardous to health Information to refer to when identifying and using hazardous substances Procedures for dealing with an incident involving hazardous substances Benefits of this course: COSHH stands for the 'Control of Substances Hazardous to Health' and falls under the Control of Substances Hazardous to Health Regulations 2002 This half day course is for all those who work, or wish to work, in a workplace that works with hazardous substances, such as in healthcare, in the manufacturing sector, cleaners, transport, utilities and even office environments Hazardous substances are everywhere, and COSHH assessments have to be undertaken in all businesses Candidates will learn about the legal requirements relating to hazardous substances, how risk assessments contribute to the safe use of hazardous substances, as well as the precautions and procedures required to ensure that the risks associated with hazardous substances are properly controlled Accredited, Ofqual regulated qualification: This QA Level 2 Award in Principles of COSHH (RQF) Course is a nationally recognised, Ofqual regulated qualification accredited by Qualsafe Awards.This means that you can be rest assured that your Principles of COSHH Certificate fulfills the legal requirements and is a very good way to make sure you and your employees are trained appropriately.The Ofqual Register number for this course is 603/0775/4

Principles of COSHH
Delivered in Chesterfield or Online + more
£85

EAL Electric Vehicle Charging Equipment Installation

4.7(1243)

By Technique Learning Solutions

This qualification aims to provide expert guidance to learners wishing to gain knowledge and understanding on Electric Vehicle charging equipment installation. This 2 day course provides expert guidance on EV charging equipment installation, an important emerging area which is not covered in detail by the current edition of the Wiring Regulations (BS 7671) or the IET’s Guidance Notes. Aimed at experienced electricians interested in understanding a wide range of equipment and systems available, this course applies to the specialised installation requirements of electric vehicle charging equipment in domestic dwellings, on-street locations, commercial and industrial premises. The course provides detailed guidance and recommendations on all aspects of the installation of Electric Vehicle Charging Equipment from the origin of the electrical supply, through distribution and final circuits, installation of the charging equipment itself to the cable between the charging equipment and vehicle’s electrical inlet. Also included are related issues of site layout and planning and subsequent inspection, testing, certification and maintenance of installations. Why take this course? Currently there is an increasing demand for new electric vehicle charging points but too few installers to roll them out. This is already a booming market which is due to get much bigger in the near future. The number of public charging connectors and locations has increased by 38% in the past 12 months and is expected to continue at that rate for years to come. Entry Requirements There are no formal entry requirements for this qualification, however we do expect you to meet the following requirements: Minimum age 18 years old (mandatory) Must be able to demonstrate the following competencies Be able to correctly install and terminate: pvc/pvc cable (twin and earth) Steel Wire armoured cable (swa) Be able to carry out an initial verification (inspection & testing) on an electrical installation and complete the necessary paperwork. Please Note: These competencies are required for the assessment and are not taught as part of the course. It is also recommended that you are up to date with your wiring regulations.

EAL Electric Vehicle Charging Equipment Installation
Delivered in Scotland + 1 more or Online + more
£500

Database fundamentals

5.0(3)

By Systems & Network Training

Database fundamentals training course description This three-day training course helps you prepare for Microsoft Technology Associate Exam 98-364, and build an understanding of these topics: Core Database Concepts, Creating Database Objects, Manipulating Data, Data Storage, and Administering a Database. What will you learn Describe core database concepts. Create database objects. Manipulate data. Describe data storage. Administer a database. Create a relational database consisting of 3 related tables. Database fundamentals training course details Who will benefit: Those working with databases. Prerequisites: None. Duration 3 days Database fundamentals training course contents Understanding core database concepts Flat-type databases, hierarchical databases, relational databases, database fundamentals, relational database concepts, using the SQL Server Management Studio Interface. Data Manipulation Language (DML), Data Definition Language (DDL), using DDL statements. Creating database objects Defining data types, using built-in data types, using exact numeric data types, using approximate numeric data types. Creating and using tables. Creating views. Creating stored procedures, SQL injections. Manipulating data Using Queries to select data, combining conditions, using the BETWEEN clause, using the NOT clause, using the UNION clause, using the EXCEPT and INTERSECT clauses, using the JOIN clause. Using Queries to insert data, Inserting data. Updating data and databases, Using the UPDATE statement. Deleting data, Using the DELETE statement, truncating a table with TRUNCATE TABLE, deleting a table with DROP TABLE, using referential integrity. Understanding data storage Normalising a database, normalization, first normal form, second normal form, third normal form, fourth normal form, fifth normal form. Primary, foreign and composite keys, clustered and non-clustered indexes, creating a non-clustered table. Administering a Database Securing Databases, server-level security, database-level security, Windows security, SQL authentication, database server roles, granting access to a database, fixed database roles, object permissions, managing roles, ownership chains, reviewing a sample security model. Backing up and restoring databases, recovery models, backup devices.

Database fundamentals
Delivered in Internationally or OnlineFlexible Dates
£2,367

Microsoft Access

5.0(3)

By Systems & Network Training

Microsoft Access training course description A hands on course providing a solid grounding in Microsoft Access. What will you learn Use and customise the Microsoft Access environment. Select, use and customise queries. Define tables. Design forms and reports. Recognise the use of macros. Microsoft Access training course details Who will benefit: Anyone wishing to work with Microsoft Access. Prerequisites: Database fundamentals Duration 3 days Microsoft Access training course contents Introducing databases Flat file databases, Relational databases, the objects defined in an Access database, planning a simple relational database. Open Access and create a database The database wizards, tables, creating and amending tables, using field properties to improve the quality of data entry and system performance, the primary key. Working in datasheet view View, add, modify and delete records, find records. Advantages and disadvantages of entering data directly into a table. Queries Sort and select records form a single table, advantages and disadvantages of entering data via a query, define simple calculated expressions, use 'Totals' queries. Forms Use the form wizards, basic editing of objects created using the form wizards, Data-entry in form view. Reports Use the report wizard, basic editing of objects created using the report wizard, print reports. The multi table environment Plan and create a related table, define a one-to-many relationship, write multi-table queries and use the 'AutoLookup' feature, use the form wizard to create a subform and carry out data-entry in a main/subform, print and amend reports, use the report wizard to create reports based on multi-table. Relationships Working with one-to-one and one-to-many relationships, recognising and handling many-to-many relationships, referential integrity. Select queries Select queries based on related tables, parameter queries, Crosstab, find unmatched queries and Find Duplicate, the implications of the Join properties in a relational query, conditional expressions, and working with the expression builder. Action queries Make table queries, append queries, update queries, delete queries. Customising forms. Using the Toolbox, calculated controls, Combo and List boxes, query by form, working with form and control properties, domain aggregate functions. Reports Report and control properties, customising sorting and grouping, calculated controls on reports, Sub-reports, editing and altering a report's source. Macros Introduction to macros.

Microsoft Access
Delivered in Internationally or OnlineFlexible Dates
£1,697

Emergency Lighting

4.7(1243)

By Technique Learning Solutions

The Emergency Lighting BS 5266 one day course is based upon BS5266:1 (including latest amendments), BS5266:7 and BS5266:8. Emergency lighting is essential for the safety of building occupants. It is vital that the emergency lighting automatically operates in the event of normal lighting failure. The illumination levels and period of time the illumination can be sustained should be sufficient to allow the building occupants to evacuate safely and locate both fire alarm, fire fighting and first aid equipment. The Emergency Lighting BS 5266 course provides the necessary information to designate emergency escape routes and design and commission an emergency lighting scheme to BS 5266. The morning of the Emergency Lighting BS 5266 course is spent reading through and interpreting the relevant parts of BS 5266. The afternoon takes the form of a practical workshop where a system is designed and the participant is then introduced to the practical issues of commissioning, inspection and testing, certification and reporting.

Emergency Lighting
Delivered in Clay Cross or Online
£500