706 Courses in Coventry

About this Course This 5 full-day course provides a comprehensive understanding of all the commissioning procedures for combined cycle power plants. The Commissioning Management System (CMS) of combined cycle power plants is covered in detail in this course. This includes all the commissioning procedures and documents, purpose of commissioning, responsibilities, system description, organization, working parties, test teams, documentation, testing and commissioning schedules, test reports, safety, plant certification, and plant completion report. The course provides also a thorough understanding of all the commissioning requirements for gas turbines, steam turbines and auxiliaries, generator and auxiliaries, electrical equipment, switchgear equipment, switchgear and transformers. All the stages of the commissioning procedure are covered in-depth in this course. This includes preparation - planning various activities, pre-commissioning checks and tests, typical commissioning schedule, detailed tests and commissioning procedures and instructions for every component in a combined cycle power plant, instrumentation, trial run of the equipment, safety and precautions, commissioning of combined cycle power plant systems, safety rules clearance certificates, procedure for the control and handling of defects, commissioning reports, operational testing, first fire, generator synchronization, performance testing, heat rate testing, emission testing, contract testing, CO2 concentration tests, electrical full-load rejection test, duct burner testing, partial load stability test, and reliability test. This course is a MUST for anyone who is involved in the pre-commissioning or commissioning of any combined cycle power plant equipment because it provides detailed pre-commissioning checks and tests, and detailed tests and commissioning procedures and instructions for every component in a combined cycle power plant. In addition, the seminar provides an in-depth coverage of all preparation, planning activities, commissioning schedules, trial run of each combined cycle power plant equipment, safety and precautions, safety rules clearance certificates, procedures for handling defects, and commissioning reports. Training Objectives Pre-commissioning Checks and Tests, Detailed Tests and Commissioning Procedures and Instructions for Every Equipment in Combined Cycle Power Plants: Gain a thorough understanding of all pre-commissioning checks and tests, and all commissioning procedures and instructions for every equipment in combined cycle power plants Commissioning Management System (CMS) of Combined Cycle Power Plants: Discover the benefits of the CMS of combined cycle power plants including all commissioning procedures and documents, purpose of commissioning, responsibilities, system description, organization, working parties, test teams, documentation, testing and commissioning schedules, test reports, safety, plant certification, and plant completion report Commissioning Procedures and Instructions for Heat Recovery Steam Generators, Air Blow and Steam Blow of Steam and Gas Piping in Combined Cycle Power Plants: Learn about the commissioning procedures and instructions for heat recovery steam generators, chemical cleaning of heat recovery steam generators, air blow and gas blow of steam and gas piping in combined cycle power plants, safety valve setting and soot blowers Commissioning Procedures and Instructions for Gas Turbines and Steam Turbines: Gain a thorough understanding of all the commissioning procedures and instructions for gas and steam turbines and auxiliaries including acid cleaning of oil pipelines, lubrication and governing system (oil flushing and hydraulic testing), jacking oil system, governing system, regenerative system, barring gear, vacuum tightness test, first rolling of turbine and data logging Commissioning Procedures and Instructions for Generator and Auxiliaries: Discover all the commissioning procedures and instructions for generator and auxiliaries including generator, seal oil system, hydrogen gas system, stator water system, rolling and start-up of generators Commissioning Procedures and Instructions for Electrical Equipment: Learn about all the commissioning procedures and instructions for electrical equipment including switchyard equipment, switchgear, transformers and motors Operational Testing, Performance Testing, Heat Rate Testing, Emission Testing of Combine Cycle Power Plants: Gain a thorough understanding of operational testing, first fire, generator synchronization, performance testing, heat rate testing, emission testing, contract testing, CO2 concentration tests, electrical full-load rejection test, duct burner testing, partial load stability test, and reliability test of combined cycle power plants Target Audience Engineers of all disciplines Managers Technicians Maintenance personnel Other technical individuals Training Methods The instructor relies on a highly interactive training method to enhance the learning process. This method ensures that all the delegates gain a complete understanding of all the topics covered. The training environment is highly stimulating, challenging, and effective because the participants will learn by case studies which will allow them to apply the material taught to their own organization. Trainer Your specialist course leader has more than 32 years of practical engineering experience with Ontario Power Generation (OPG), one of the largest electric utility in North America. He was previously involved in research on power generation equipment with Atomic Energy of Canada Limited at their Chalk River and Whiteshell Nuclear Research Laboratories. While working at OPG, he acted as a Training Manager, Engineering Supervisor, System Responsible Engineer and Design Engineer. During the period of time, he worked as a Field Engineer and Design Engineer, he was responsible for the operation, maintenance, diagnostics, and testing of gas turbines, steam turbines, generators, motors, transformers, inverters, valves, pumps, compressors, instrumentation and control systems. Further, his responsibilities included designing, engineering, diagnosing equipment problems and recommending solutions to repair deficiencies and improve system performance, supervising engineers, setting up preventive maintenance programs, writing Operating and Design Manuals, and commissioning new equipment. Later, he worked as the manager of a section dedicated to providing training for the staff at the power stations. The training provided by him covered in detail the various equipment and systems used in power stations. In addition, he has taught courses and seminars to more than four thousand working engineers and professionals around the world, specifically Europe and North America. He has been consistently ranked as 'Excellent' or 'Very Good' by the delegates who attended his seminars and lectures. He written 5 books for working engineers from which 3 have been published by McGraw-Hill, New York. Below is a list of the books authored by him; Power Generation Handbook: Gas Turbines, Steam Power Plants, Co-generation, and Combined Cycles, second edition, (800 pages), McGraw-Hill, New York, October 2011. Electrical Equipment Handbook (600 pages), McGraw-Hill, New York, March 2003. Power Plant Equipment Operation and Maintenance Guide (800 pages), McGraw-Hill, New York, January 2012. Industrial Instrumentation and Modern Control Systems (400 pages), Custom Publishing, University of Toronto, University of Toronto Custom Publishing (1999). Industrial Equipment (600 pages), Custom Publishing, University of Toronto, University of Toronto, University of Toronto Custom Publishing (1999). Furthermore, he has received the following awards: The first 'Excellence in Teaching' award offered by PowerEdge, Singapore, in December 2016 The first 'Excellence in Teaching' award offered by the Professional Development Center at University of Toronto (May, 1996). The 'Excellence in Teaching Award' in April 2007 offered by TUV Akademie (TUV Akademie is one of the largest Professional Development centre in world, it is based in Germany and the United Arab Emirates, and provides engineering training to engineers and managers across Europe and the Middle East). Awarded graduation 'With Distinction' from Dalhousie University when completed Bachelor of Engineering degree (1983). Lastly, he was awarded his Bachelor of Engineering Degree 'with distinction' from Dalhousie University, Halifax, Nova Scotia, Canada. He also received a Master of Applied Science in Engineering (M.A.Sc.) from the University of Ottawa, Canada. He is also a member of the Association of Professional Engineers in the province of Ontario, Canada. POST TRAINING COACHING SUPPORT (OPTIONAL) To further optimise your learning experience from our courses, we also offer individualized 'One to One' coaching support for 2 hours post training. We can help improve your competence in your chosen area of interest, based on your learning needs and available hours. This is a great opportunity to improve your capability and confidence in a particular area of expertise. It will be delivered over a secure video conference call by one of our senior trainers. They will work with you to create a tailor-made coaching program that will help you achieve your goals faster. Request for further information post training support and fees applicable Accreditions And Affliations

REFERENCE CODE 603/7493/7 COURSE LEVEL NVQ Level 2 THIS COURSE IS AVAILABLE IN Course Overview The Level 2 NVQ in Insulation & Building treatments is for those who work with different types of insulation and building treatments and want to prove their competence in one or more of the following areas: Wood preserving and damp-proofing, Wall Tie replacement, Cavity Wall insulation, Solid Floor insulation, Under Floor insulation and Cold Roof insulation. There is also a Level 2 qualification available that may be more suitable for those in the sector with a greater degree of experience or level of responsibility

REFERENCE CODE 610/0075/3 COURSE LEVEL NVQ Level 2 THIS COURSE IS AVAILABLE IN Course Overview This qualification is aimed at individuals wishing to prove they have the level and range of knowledge and skills required to install Interior Systems in the Construction working environment. It is not expected that all workers will complete the same tasks, there are 3 mandatory units common to all pathways. The Pathways will allow employees with specific skills and from companies of all sizes equal opportunity to complete. All work must be completed following Industry recognised Safe Working Practices and in accordance with relevant legislation. This qualification is at Level 2, although some units may be at different levels and should be taken by those who are fully trained to deal with a range of tasks and situations. There is also a Level 2 Certificate and a Level 3 Diploma in Interior Systems available.

REFERENCE CODE 603/2369/3 COURSE LEVEL NVQ Level 2 THIS COURSE IS AVAILABLE IN Course Overview This qualification is aimed those who carry out activities in the Construction Industry working with Glass Reinforced Plastics (GRP) products. The qualification has a core group of 5 mandatory units that cover the generic areas including Health and Safety, transport and storage of tools, materials and equipment, checking and confirming the job specification and communication skills. The qualification also has a group of optional units that cover preparation, positioning, testing, installation and assembly. The qualification, along with the required separate proof of Health and Safety knowledge will give candidates a route to the relevant CSCS card required for site access.

REFERENCE CODE 601/8330/5 COURSE LEVEL NVQ Level 2 THIS COURSE IS AVAILABLE IN Course Overview This qualification is aimed at those who are involved in installing roof sheeting and cladding systems and associated tasks on site working from drawings and specifications. It is not expected that candidates working in this industry all do the same activities or use the same equipment and machinery so there is a group of optional units to cover these matters, however all candidates will need to prove competence in preparing the resources required, installation of sheeting and cladding systems and rainwater goods (gutters, pipes, downpipes and angles (swan necks, off sets), brackets and supports, sumps, overflows and outlets). All work completed must be carried out in accordance with Building Regulations and Industry recognised safe working practices, including the disposal of waste. The qualification is structured to ensure that there is a high degree of flexibility within the units available and will allow employees from companies of all sizes and specialisms equal opportunity to complete. To provide this opportunity in addition to the core skills above, candidates will also be able to select optional units recognising skills including, repair and/or refurbishment of roof sheeting/cladding/rainscreen systems, working with boom and/or scissor type mobile elevating platforms (MEWPs), installing solar collectors, use of ergonomic manipulating machines or slinging/signalling the movement of loads.

REFERENCE CODE 601/8331/7 COURSE LEVEL NVQ Level 3 THIS COURSE IS AVAILABLE IN Course Overview This qualification is aimed at those who are involved in installing Rainscreen wall cladding systems and/or roof sheeting and cladding systems that involve curved and complex roof and wall formations in the workplace, working from drawings and specifications. It is not expected that candidates working in this industry all do the same activities or use the same equipment and machinery so the qualification has been developed to make it as widely available as possible by having 2 distinct pathways. All work completed must be carried out in accordance with Building Regulations and Industry recognised safe working practices, including the disposal of waste. The qualification is structured to ensure that there is a high degree of flexibility within the units available and will allow employees from companies of all sizes and specialisms equal opportunity to complete. To provide this opportunity in addition to the relevant mandatory pathway units of installation of the relevant system (roof and wall sheeting and cladding or rainscreen wall cladding systems) , candidates will also be able to select optional units recognising skills including, repair and/or refurbishment of roof sheeting/cladding/rainscreen systems, working with boom and/or scissor type mobile elevating platforms (MEWPs), installing solar collectors, use of ergonomic manipulating machines or slinging/signalling the movement of loads. The standards cover the most important aspects of the job. This qualification is at Level 3, although some units may be at different levels, qualifications at this level are primarily aimed at those who are fully trained and experienced in a wide range of roles that may involve decision making, quality checks, work planning and dealing with non-routine or complex installations. The qualification consists of 3 mandatory units and 2 pathways, Wall sheeting and cladding and Rainscreen Wall Systems. Candidates must achieve the 3 qualification mandatory units plus the required credits from the selected pathway. The minimum credit value of the Wall sheeting and cladding qualification is 132 credits, the minimum credit value of the Rainscreen wall systems qualification is 104 credits.

REFERENCE CODE 603/5285/1 COURSE LEVEL NVQ Level 2 THIS COURSE IS AVAILABLE IN Course Overview Who is this qualification for? This is a work-based learning qualification for those involved in laying floorcoverings in a Construction related working environment. Although many of the skills and knowledge across floorcovering occupations are generic, not all those employed to fit floorcoverings will be fitting the same product. The group of optional units will allow specialisms of timber based, textile and resilient floorcoverings. What is required from candidates? To achieve this pathway unit the survey work must be carried out in ways that will minimise the risk of damage to the work and surrounding area and using and maintaining equipment effectively. This qualification is made up of 9 mandatory units and a group of optional units. The minimum credit value of this qualification is 127 credits. Qualifications are now required to indicate the total qualification time (TQT), this is to show the typical time it will take someone to attain the required skills and knowledge to meet the qualification criteria, this qualification has a TQT of 1,270 hours. Qualifications are also required to indicate the number of hours of teaching someone would normally need to gain the skills and knowledge to achieve the qualification. These are referred to as Guided Learning Hours (GLH). The GLH for this qualification is 543 Mandatory units Level Credit Conforming to General Health, Safety and Welfare in the Workplace Conforming to Productive Working Practices in the Workplace Moving, Handling and Storing Resources in the Workplace Surface preparation to receive floorcoverings in the workplace Setting out for laying floorcoverings in the workplace Preparing and fitting underlays for floorcoverings in the workplace Develop customer relationships Assessing and preparing background surfaces for floor-covering in the workplace Assessing and evaluating conditions for floorcoverings in the workplace Optional Units (Minimum of 18 credits) Installing timber–based floorcoverings in the workplace Summary of the: GQA NVQ LEVEL 2 DIPLOMA IN FLOORCOVERING OCCUPATIONS (CONSTRUCTION) Installing textile floorcoverings in the workplace Installing resilient floorcoverings in the workplace Types of evidence: Evidence of knowledge is required. Evidence of knowledge through performance can contribute and if applicable should be demonstrated by completing projects and reports, by responding to questions or through Professional/Guided Discussions. Quantity of evidence: Evidence should show that you can meet the requirements of the units consistently over an appropriate period of time. Potential sources of evidence: Suggested sources of evidence are shown above, these can be supplemented by physical or documentary evidence, e.g.: Accident book/reporting system Notes and memos Safety record Telephone/e-mail records Training record Customer and colleague feedback Audio evidence Records of equipment and materials Witness testimonies Work records Photographic/ video evidence Please Note that photocopied or downloaded documents such as manufacturers or industry guidance, H&S policies, Risk Assessments etc, are not normally acceptable evidence for GQA qualifications unless accompanied by a record of a professional discussion or assessor statement confirming candidate knowledge of the subject. If you are in any doubt about the validity of evidence, please contact Oscar Onsite Academy

REFERENCE CODE 603/5204/8 COURSE LEVEL NVQ Level 3 THIS COURSE IS AVAILABLE IN Course Overview Who is this Qualification for? This qualification is aimed those who carry out supervisory activities in a specific trade in the Construction Industry. The qualification certificate will carry an endorsement to show what trades the candidate was supervising during completion of this qualification. The qualification has a core group of 5 mandatory units that cover areas including Health and Safety, confirming work requirements and coordinating work operations. The qualification also has a group of optional units to allow flexibility to suit individual needs and responsibilities and completion of mandatory units and a minimum of 2 units from the optional group will give access to the relevant CSCS card. This qualification replaces version 1 of the GQA Level 3 NVQ Diploma in Occupational Work Supervision (Construction) QAN 601/3469/0 for anyone starting the qualification from 01/11/2019. What is required from candidates? This qualification consists of 5 mandatory units, which have a total of 57 credits and a group of optional units. Candidates must complete all 5 mandatory units and a minimum of 2 units from the optional group. GQA qualifications are made up of units that have a credit value or credits. These credits must be achieved in the correct combination of mandatory and optional units. Qualifications are now required to indicate the total qualification time (TQT), this is to show the typical time it will take someone to attain the required skills and knowledge to meet the qualification criteria. The units of assessment set out learning outcomes which describe what learners need to be able to do and understand. The learning outcomes are defined by assessment criteria which are used to assess competence, expressed as skills achieved and learned knowledge and understanding, to achieve the units. Achievement of the mandatory units and chosen optional units will mean the qualification has been completed and will be subject to approval of a claim for certification. GQA Qualifications will issue a certificate complete with the learner’s name, the qualification and unit titles and the credits achieved. Mandatory units Level Credit Confirming Work Activities and Resources for an Occupational Work Area in the Workplace Developing and Maintaining Good Occupational Working Relationships in the Workplace Confirming the Occupational Method of Work in the Workplace Implementing and maintaining health, safety and welfare in the workplace Coordinating and organising work operations in the workplace Optional Units – Minimum of 2 units (19 credits must be achieved) Allocating and monitoring the use of plant, machinery, equipment or vehicles in the workplace Monitoring progress of work against schedules in the workplace Confirming work meets contractual, industry and manufacturers’ standards in the workplace Implementing procedures to support the team performance in the workplace 3 13 Co-ordinating and confirming the dimensional control requirements of the work in the workplace Entry requirements There are no formal entry requirements for learners undertaking this qualification. However, centres must ensure that learners have the potential and opportunity to gain the qualification successfully. Qualification support This qualification has been designed and developed by CITB and GQA Qualifications have authorised Oscar Onsite Academy to deliver this qualification in the Construction Sector. Please Note that photocopied or downloaded documents such as manufacturers or industry guidance, H&S policies, Risk Assessments etc, are not normally acceptable evidence for Oscar Onsite Qualifications unless accompanied by a record of a professional discussion or Assessor statement confirming candidate knowledge of the subject. If you are in any doubt about the validity of evidence, please contact Oscar Onsite Academy

REFERENCE CODE 601/4322/8 COURSE LEVEL NVQ Level 3 THIS COURSE IS AVAILABLE IN Course Overview Who is this qualification for? This qualification is aimed at those who are involved in Plastering activities in the workplace. It is not expected that candidates working in this industry all do the same activities so the qualification has been developed to allow opportunities for those carrying out work in either solid or fibrous Plastering. Those taking the qualification must also prove knowledge and competence in working at heights, calculating quantities and wastage and the use of powered and hand tools and equipment. All work completed must be done in accordance with Building Regulations and Industry recognised safe working practices, including the disposal of waste. The qualification is structured to ensure that there is a high degree of flexibility within the units available and will allow employees from companies of all sizes and specialisms equal opportunity to complete. See the qualification Rules of Combination for more details on the specific skills required. In addition to this qualification there is a Level 2 qualification in Plastering and a number of other Construction and Construction related qualifications available through Oscar Onsite Academy. What is required from candidates? GQA qualifications are made up of a number of units that have a credit value or credits. This qualification consists of 4 mandatory units and 2 pathways, Solid and Fibrous. The qualification mandatory units have a total credit value of 31 credits-in addition the Solid plastering pathway requires achievement of 54 credits from the pathway mandatory units and a minimum of 14 credits required from the pathway optional group, giving a total of 99 credits. The fibrous plastering pathway requires achievement of all of the qualification mandatory units (31 credits) 45 credits from the pathway mandatory units and a minimum of 16 credits required from the pathway optional group a total of 92 credits for this pathway. The units are made up of the things those working in these job roles need to know to be able to do to carry out the work safely and correctly. These are called Learning Outcomes, and all must be met to achieve the unit. Mandatory units Level Credit Confirming Work Activities and Resources for an Occupational Work Area in the Workplace Developing and Maintaining Good Occupational Working Relationships in the Workplace Confirming the Occupational Method of Work in the Workplace Conforming to General Health, Safety and Welfare in the Workplace Additional units A/600/7882 Producing Granolithic Paving Work in the Workplace Producing Specialised Plasterer’s Surfaces in the Workplace 3 29 Pathway C – Solid – Pathway C1 – Solid Mandatory Units (54 credits) Producing Complex Internal Solid Plastering Finishes in the Workplace 3 27 Producing Complex External Rendering Finishes in the Workplace 3 27 Pathway C2 – Solid Optional Units – candidates must achieve a minimum of 14 credits Installing Direct Bond Dry Linings in the Workplace Installing Mechanically Fixed Plasterboard in the Workplace Running In-situ Mouldings in the Workplace Pathway D – Fibrous – Pathway D1 – Fibrous Mandatory Units (45 credits) Producing Complex Plasterwork Moulds in the Workplace Summary of the: GQA LEVEL 3 NVQ DIPLOMA IN PLASTERING (CONSTRUCTION) Installing Complex Fibrous Plaster Components in the Workplace 3 18 Pathway D2 – Fibrous Optional Units – candidates must achieve a minimum of 16 credits Running In-situ Mouldings in the Workplace 3 25 Repairing Complex Fibrous Plaster Components in the Workplace 3 16 Assessment Guidance Evidence should show that you can complete all of the learning outcomes for each unit being taken. Types of evidence: Evidence of performance and knowledge is required. Evidence of performance should be demonstrated by activities and outcomes, and should be generated in the workplace only, unless indicated under potential sources of evidence (see below). Evidence of knowledge can be demonstrated though performance or by responding to questions. Quantity of evidence: Evidence should show that you can meet the requirements of the units in a way that demonstrates that the standards can be achieved consistently over an appropriate period of time. Potential sources of evidence: Suggested sources of evidence are shown above, these can be supplemented by physical or documentary evidence, e.g. Accident book/reporting system Notes and memos Safety record Telephone/e-mail records Training record Customer and colleague feedback Audio evidence Records of equipment and materials Witness testimonies Work records Photographic/ video evidence Please Note that photocopied or downloaded documents such as manufacturers or industry guidance, H&S policies, Risk Assessments etc, are not normally acceptable evidence for qualifications unless accompanied by a record of a professional discussion or Assessor statement confirming candidate knowledge of the subject. If you are in any doubt about the validity of evidence, please contact Oscar Onsite Academy

WANT TO LOSE WEIGHT, HAVE MORE ENERGY AND FEEL MORE HAPPY? The Menopause Lifestyle Project is a group programme and an opportunity to work with me in person, in the studio. The 4 week course is educational and will introduce you to what menopause is, why it happens, symptoms related to it and how you can best manage your lifestyle during this period. There is also be an introduction to strength training and a video programme to follow, either at home or in the gym. For more details on the next programme please get in touch.