4 Educators providing FITT courses in Cardiff

Platelet-rich Plasma (PRP) treatments Nationally Recognised Qualification No previous experience or qualifications needed Open College Network Accreditation Level 4 (as required for minimally invasive procedures) Covers standards set by HEE Employed (salon) or Self-Employed opportunities Basic understanding of English language required OPEN TO ALL APPLICANTS

About this Training Course The drill string is the simplest piece of equipment in use on a drilling rig and at the same time, the most critical piece. We use the qualifier 'basic' because although 99% of the drill string comprises plain tubes that are just screwed together, the lowest section, just above the bit, can go to extreme loading and is fitted with highly sophisticated electronics packages providing both positional and lithological data as well as a steering system to drive and orient the bit. The principle tasks of the drill string are also deceptively simple. These are to: Convey each drill bit to the bottom of the hole and then to retrieve it when worn, Act as a conduit to convey drilling fluid at high pressure down to the bit and Transmit torque from surface to bit, occasionally in concert with a hydraulic motor to drive this bit. This 3 full-day course will cover in detail what it takes to decide on minimum drill string specifications, which are able to support the loads to which it will be subjected. In addition to the need to use a drill string with minimum strength requirements, we also need to ensure that we can prevent drill string failure. If the failure consists of a small split or leak of any kind, then the time involved may be little more than that required for a roundtrip to change the bit. If the string parts, then the recovery is likely to take a considerable amount of time. In a worst case scenario, the fish in the hole may prove impossible to retrieve, requiring a sidetrack. A less than optimal design of the string will reduce the efficiency of the operation and almost always leads to premature bit wear. This is particularly true when we are unable to measure and control the dynamics of the drill string as a whole and the bottomhole assembly in particular. Axial vibrations, torsional vibrations and lateral vibrations may take place in various degrees of severity. The behaviour of the drill string while operating under torsional vibrations is thought to be of great importance and may result in torsional buckling. This course will also cover the drilling optimization limiters, how to identify them and how to remove them. This is done by understanding the drill string dynamics - by operating under the most favourable conditions and by measuring the dynamics in the vicinity of the bit (or at the bit) in order to make timely adjustments. Training Objectives The course homes in what office staff needs to know and plan for and what field staff needs to know and implement. By the end of this course, participants will be familiar with: Critical dimensions of common drill pipe and weld-on tool joints and its relation to yield for calculation of tensile, torsional and burst resistance. Make-up torque of connections that relate to the tool joint dimensions and the torsional strength of that connection. Use of design factors and safety factors on tensile and torsional strength in relation to new and worn state. Conditions which could lead to drill pipe collapse. Situations where limitations on sinusoidal (snake) and helical buckling will apply and the influence of radial clearance and deviation. Failure of drill pipe (fatigue) and the circumstances under which these would occur (rotation across doglegs, pipe in compression etc). Mechanism under which hardbanding would induce casing wear and the methods applied to measure and prevent any significant wear. Drill pipe inspection methods we apply to identify early flaws/cracks/corrosion, to measure dimensions, to inspect tool joints etc. Common BHA components, including heavy wall drill pipe, their external/internal dimensions, connections (API, proprietary) and appearance (such as spiral). Significance of thread compounds to ensure the correct make-up torque is applied. Significance of drill string/BHA 'neutral point' in the context of drill string component failure. Basic design principles for a BHA make-up in a vertical, low/medium deviated and highly deviated well in terms of weight transfer and drag/torque. Stabilization principles for a pendulum (vertical), a stabilized (vertical or tangent), a build and a drop-off assembly. BHA design and stabilization in relation to mitigation/elimination of vibration and to the elimination of tension, torsion or fatigue failure. Matching bit aggressiveness, gauge length, BHA stabilization, steerability and Mechanical Specific Energy (MSE) to mitigate the severity of any vibration. Bit efficiency and reduction of wear by understanding mechanical and hydraulic limiters. How to perform a passive or active drill-off test. Importance of being conversant with API 7G RP and/or equivalent data books, to look up/check the recommended tensile/torque and other parameters for the drill string in use. Target Audience This course is intended for staff directly or indirectly involved in the delivery of challenging wells such as junior to senior well engineers, both in office-based planning and operations and field-based operator/contractor supervisory staff such as company men and toolpushers. Trainer Your expert course leader has over 45 years of experience in the Oil & Gas industry. During that time, he has worked exclusively in the well engineering domain. After being employed in 1974 by Shell, one of the major oil & gas producing operators, he worked as an apprentice on drilling rigs in the Netherlands. After a year, he was sent for his first international assignment to the Sultanate of Oman where he climbed up the career ladder from Assistant Driller, to Driller, to wellsite Petroleum Engineer and eventually on-site Drilling Supervisor, actively engaged in the drilling of development and exploration wells in almost every corner of this vast desert area. At that time, drilling techniques were fairly basic and safety was just a buzz word, but such a situation propels learning and the fruits of 'doing-the-basics' are still reaped today when standing in front of a class. After some seven years in the Middle East, a series of other international assignments followed in places like the United Kingdom, Indonesia, Turkey, Denmark, China, Malaysia, and Russia. Apart from on-site drilling supervisory jobs on various types of drilling rigs (such as helicopter rigs) and working environments (such as jungle and artic), he was also assigned to research, to projects and to the company's learning centre. In research, he was responsible for promoting directional drilling and surveying and advised on the first horizontal wells being drilled, in projects, he was responsible for a high pressure drilling campaign in Nigeria while in the learning centre, he looked after the development of new engineers joining the company after graduating from university. He was also involved in international well control certification and served as chairman for a period of three years. In the last years of his active career, he worked again in China as a staff development manager, a position he nurtured because he was able to pass on his knowledge to a vast number of new employees once again. After retiring in 2015, he has delivered well engineering related courses in Australia, Indonesia, Brunei, Malaysia, China, South Korea, Thailand, India, Dubai, Qatar, Kuwait, The Netherlands, and the United States. The training he provides includes well control to obtain certification in drilling and well intervention, extended reach drilling, high pressure-high temperature drilling, stuck pipe prevention and a number of other ad-hoc courses. He thoroughly enjoys training and is keen to continue taking classes as an instructor for some time to come. POST TRAINING COACHING SUPPORT (OPTIONAL) To further optimise your learning experience from our courses, we also offer individualized 'One to One' coaching support for 2 hours post training. We can help improve your competence in your chosen area of interest, based on your learning needs and available hours. This is a great opportunity to improve your capability and confidence in a particular area of expertise. It will be delivered over a secure video conference call by one of our senior trainers. They will work with you to create a tailor-made coaching program that will help you achieve your goals faster. Request for further information post training support and fees applicable Accreditions And Affliations

OFTEC Domestic Oil Course (Initial)

Domestic Oil (aka OFTEC Courses)

Expand your scope and become a Domestic LPG install/service/maintenance/breakdown engineer today! Or, renew your LPG qualifications for a great price whilst improving your skills & knowledge! This course is the ACS LPG Changeover, you will be asked if you require Initial or Renewal at check out.

This course covers all relevant health and safety laws including Working at Height Regulations 2005.

Renew your solid fuel certificate whether you're HETA, BPEC, OFTEC, or C&G! Become a solid fuel installer & servicer today!

This course is suitable for Solid Fuel engineers who are looking to re-new their previous certification. Our Initial course is available through this link: https://www.citytraining.com/w/courses/21-solid-fuel-initial Dry - 1 Day Wet - 2 Days Our courses are accredited by OFTEC and certified by Cert-ain, but this does not stop you from renewing or achieving accreditation from HETAS and similar bodies, saving you money on training costs too. What's included? DryOFT15-108(D) - Installation, commissioning, and servicing of solid fuel burning appliances (dry space heating).OFT18-108(S) - Service, maintenance, repair, or commissioning of solid fuel burning appliances. WetAs above [OFT15-108(D) & OFT18-108(S)].OFT15-108(W) - Installation, commissioning, and servicing of solid fuel burning appliances with space heating and hot water heating. Prerequisites Category 1 - RENEWAL (this course) Applicants in this category are regarded as experienced Solid Fuel technicians holding one of the following - they will need to provide an original certificate as evidence to the Assessment Centre prior to taking OFTEC assessments:  OFTEC OFT15-108D (category 1 status for OFT15-108D and OFT18-108S) OFT15-108W (category 1 status for OFT15-108W, OFT15-108D and OFT18-108S) OFT18-108S (category 1 status for OFT18-108S only) HETAS H003 AND H006 (category 1 status for OFT15-108D and OFT18-108S) H004 AND H006 (category 1 status for OFT15-108W, OFT15-108D and OFT18-108S)H005 (category 1 status for OFT15-108W, OFT15-108D and OFT18-108S) H009 (category 1 status for OFT18-108S only) BPEC Solid Fuel Installer (category 1 status for OFT15-108W, OFT15-108D and OFT18-108S) CITY & GUILDS Level 3 NVQ Diploma in Domestic Plumbing and Heating (6189) - must include Solid Fuel pathway (category 1 status for OFT15-108W, OFT15-108D and OFT18-108S)Level 3 Diploma in Plumbing and Domestic Heating (9189-03) - must include Solid Fuel pathway (category 1 status for OFT15-108W, OFT15-108D and OFT18-108S) Category 2 (Heating Engineer - Other Fuel) - (Initial Only)Applicants in this category are regarded as holding a nationally recognised qualification in a trade associated with Solid Fuel work; candidates must provide relevant qualifications to support entry: For those looking to expand into Solid Fuel, please visit our Solid Fuel Initial page! DryOFTEC technician with scope of work categories 101,102 or 105Eor - Registered Gas Safe or RGII operativeor - Registered member of GOMCS, APICS, NACS, NIACS, CSAI, ICS, CSA or NACEor - evidence of formal qualifications: City & Guilds 6129/6035 and 6089, or QCF 6189;or - (United Kingdom) N/SVQ Level 2/3 in plumbing or equivalent earlier certification that provides evidence of competenceor - (Republic of Ireland) FETAC Level 5 in plumbingor - HETAS H003 Dry Appliance Installer courseor - BPEC Solid Fuel Installer or Solid Biomass courseor - APHC Installation of Solid Fuel Appliances and Heating Systems Fed by Solid Fuel in Domestic Appliances courseor have relevant qualifications, skills and experience gained from working in a related trade such as Plumbing / Heating / Ventilation / Refrigeration / Air-Conditioning / Gas Fitting or servicing. Applicants must provide evidence of this related experience to the Assessment Centre. The evidence must consist of, as a minimum, the following:Name and address of the business(s) providing the related experience.The types of related work undertaken (minimum 4/5 jobs). Wet Compulsory: OFTEC OFT15-108D AND (United Kingdom) - N/SVQ Level 2/3 in plumbing or equivalent earlier certification that provides evidence of competence (Republic of Ireland) - FETAC Level 6 in plumbing or - evidence of OFTEC 101 or 105E; or - evidence of formal qualifications: City & Guilds 6035 and 6089, or QCF 6189; or - HETAS H004 Wet Appliance Installer course or - BPEC Solid Biomass course or - Gas Safe Registered Operative holding a current CENWAT category or - RGII Registered Operative holding a current GID category All Category 2 candidates must also undertake training at an OFTEC approved training centre. The training must consist of training utilising the current OFTEC Technical Book. The possession of the OFTEC Technical Book prior to training and subsequent assessment is mandatory. Category 3 (New to Industry - Dry Only) - (Initial Only) Applicants in this category are regarded as new to the Solid Fuel industry, and do not hold any national qualifications in a related field nor have any related work experience. Application conditions for this category require that the Category 3 applicant must obtain experience with a business which is willing to provide an auditable extended Solid Fuel training programme incorporating both On and Off the Job components with organisational support prior to the applicant taking OFTEC training and assessment. Evidence of the contents of the programme detailing the Off the Job training and On the Job experience must be presented to the Assessment Centre as above. 4 to 5 jobs are required as a minimum for your portfolio.

NPORS Crawler Crane (N103)

NPORS Excavator as a Crane (N100)