Fibre Optic Technician courses in Sheffield

Duration 3 Days 18 CPD hours This course is intended for This course is intended for the following technical professionals who need to use advanced features of fiber optics technology: System installers System integrators System administrators Network administrators Solutions designers Overview After taking this course, you should be able to: Perform the ONS 15454 MSTP node turn-up procedure Describe first generation mesh topologies Describe the Optical Channel Network Connection (OCHNC) prerequisite requirements for provisioning circuits in an ONS 15454 MSTP network Describe the ONS MSTP advanced protocols Describe the OCHNC circuit provisioning for Single Module (SM) Reconfigurable Optical Add-Drop Multiplexer (ROADM) rings Describe the Any-Rate Muxponder Crossponder (AR MXP/XP) cards Describe how the Pseudo Command Line can be used to configure muxponder cards Identify the advantages G.709 encapsulation brings to optical transponder cards Install and provision the Any Rate cards Describe the 100-Gbps and 200-Gbps cards Describe the NCS 2000 400-Gbps Xponder line card and how it is configured Describe the SM ROADM (SMR)-based configurations Describe the 10-Gbps transponder and muxponder cards List the 10GE_XP and GE_XP card options Describe ingress policing and basic egress queuing strategies, and implement the customer QoS scheme into the ONS 15454 crossponder network Identify the principles of Ethernet related to the operation of Cisco optical networking products Configure the 10GE_XP/XPE and GE_XP/XPE cards, install Layer 1 circuits, and read the performance counters for Layer 1 Gigabit Ethernet circuits Turn up an encrypted network and test to ensure that information being passed is secure Add a node to an existing DWDM ring Describe problems with interconnecting circuits between rings, the ONS 15454 MSTP 80-channel manual Multiring feature, and hardware components Describe the ONS 15454 MSTP Troubleshooting Guide The Cisco Optical Technology Advanced (OPT300) v2.0 course gives you the skills you need to deploy advanced features of the Cisco© Optical Networking Services (ONS) 15454 Multiservice Transport Platform (MSTP) and Cisco Network Convergence System (NCS) 2000 Series. In this course you?ll learn to how to use the Cisco Transport Planner Design Tool to create network topologies and advanced network topologies. You will learn how to use advanced Dense Wavelength Division Multiplexing (DWDM) features such as G.709 encapsulation, generic framing protocol G.7041, Layer 1 circuits, Quality of Service (QoS), crossponder networks using T1 over Ethernet, and encryption. Course Outline Cisco Transport Planner Design Tool First-Generation Mesh Topologies Ochnc In A Mesh Network Advanced Protocols Any Rate Muxponder And Crossponders 100-Gbps And 200-Gbps Transponders And Muxponders Cisco Ncs 2000 400-Gbps Xponder Line Card Cisco 10G Web Security Essentials (Wse) Network Encryption Card Adding A New Location With Cisco Transport Planner (Ctp) And Cisco Transport Controller (Ctc) Crossponders And Layer 1 Networks Crossponders And Layer 2 Networks Troubleshooting Additional course details: Nexus Humans Cisco Optical Technology Advanced v2.0 (OPT300) training program is a workshop that presents an invigorating mix of sessions, lessons, and masterclasses meticulously crafted to propel your learning expedition forward. This immersive bootcamp-style experience boasts interactive lectures, hands-on labs, and collaborative hackathons, all strategically designed to fortify fundamental concepts. Guided by seasoned coaches, each session offers priceless insights and practical skills crucial for honing your expertise. Whether you're stepping into the realm of professional skills or a seasoned professional, this comprehensive course ensures you're equipped with the knowledge and prowess necessary for success. While we feel this is the best course for the Cisco Optical Technology Advanced v2.0 (OPT300) course and one of our Top 10 we encourage you to read the course outline to make sure it is the right content for you. Additionally, private sessions, closed classes or dedicated events are available both live online and at our training centres in Dublin and London, as well as at your offices anywhere in the UK, Ireland or across EMEA.

Duration 4 Days 24 CPD hours This course is intended for This course is intended for: System engineers Technical support personnel Channel partners and resellers Overview After taking this course, you should be able to: Describe Cisco DWDM platform basics Describe DWDM network topologies Describe the management software used for managing Cisco DWDM networks List the different hardware components of the Cisco ONS and Cisco NCS DWDM systems Provision nodes and circuits in a Cisco DWDM network Perform node and multishelf configurations Implement SMR-based rings Provision optical circuit protection mechanisms Configure Any Rate cards Describe the function of Raman amplifiers Perform basic maintenance and troubleshooting of a Cisco DWDM network The Cisco Optical Technology Intermediate (OPT200) v3.0 course is designed to teach you the skills necessary to deploy the Cisco© Optical Networking System (ONS), 15454 Multiservice Transport Platform (MSTP), and Cisco Network Convergence System (NCS) 2000 Series Dense Wavelength-Division Multiplexing (DWDM) networks from installation to protection. Through a combination of lecture and hands-on experience, you will learn installation, configuration, circuit protection, maintenance, and basic troubleshooting using the Cisco Transport Controller for the Cisco ONS 15454 M6 and M12 shelves, and for the Cisco NCS 2016 shelf.Additionally, in this course you will review DWDM terminology and components, explore available chassis and cards, and discuss hardware installation. You will learn to use the Cisco Transport Controller server software to connect to the nodes, perform network turn-up and circuit creation, and deploy linear and single-module ROADM (SMR) DWDM multishelf topologies. Using this software, you will also configure Raman amplifiers and Any Rate cards, and configure protected and unprotected circuits. The course covers a variety of card options: controllers, transponders, multiplexer-demultiplexer, add/drop, Raman amplifiers, and Cisco Any Rate muxponder cards. You will use the various cards to configure terminal, amplifier, mesh, split, Optical Service Channel (OSC) regenerator, and Reconfigurable Optical Add/Drop Multiplexing (ROADM) nodes. Finally, you will learn how to use many of the tools and features available with the Cisco Transport Controller to perform maintenance, testing, and basic troubleshooting of your optical network. Course Outline DWDM Optical Platform Foundation Chassis and Cards Hardware Installation Node Turn-Up and Circuit Creation Node and Multishelf Configurations SMR-Based Rings 10Gb Circuit Protection Any Rate Card Configuration Raman Amplifiers Maintenance and Basic Troubleshooting Additional course details: Nexus Humans Cisco Optical Technology Intermediate v3.0 (OPT200) training program is a workshop that presents an invigorating mix of sessions, lessons, and masterclasses meticulously crafted to propel your learning expedition forward. This immersive bootcamp-style experience boasts interactive lectures, hands-on labs, and collaborative hackathons, all strategically designed to fortify fundamental concepts. Guided by seasoned coaches, each session offers priceless insights and practical skills crucial for honing your expertise. Whether you're stepping into the realm of professional skills or a seasoned professional, this comprehensive course ensures you're equipped with the knowledge and prowess necessary for success. While we feel this is the best course for the Cisco Optical Technology Intermediate v3.0 (OPT200) course and one of our Top 10 we encourage you to read the course outline to make sure it is the right content for you. Additionally, private sessions, closed classes or dedicated events are available both live online and at our training centres in Dublin and London, as well as at your offices anywhere in the UK, Ireland or across EMEA.

Duration 4 Days 24 CPD hours This course is intended for The primary audience for this course is as follows: Technical professionals who are responsible for installation, deployment, and maintenance of the Cisco ONS 15454 MSTP network Network operations, planners, and designers Network operations engineers Overview Upon completing this course, the learner will be able to meet these overall objectives: Connect to a Cisco ONS 15454 MSTP chassis using Cisco Transport Controller (CTC) Identify Node configurations according to card population Provision DWDM circuits using the Cisco Transport Controller (CTC) Conduct performance monitoring, alarm verification, and fault isolation Provision M12 WSS in linear and M6 SMR nodes in ring topologies Configuration options for the any rate muxponder and crossponder Perform Raman amplifier initialization Isolate optical network issues In this course, you will learn the skills necessary to deploy a Cisco Network Convergence System (NCS) 2000 Series network. You will also learn how to perform node turnup. The course covers three shelf types, the Cisco ONS 15454 M12 Multiservice Transport Platform (MSTP), NCS 2006, and NCS 2002. You will learn how to deploy linear and ring dense-wavelength-division-multiplexing (DWDM) topologies. The course covers multiplexer-demultiplexer cards, Erbium-doped-fiber amplifier cards, Raman amplifiers, transponder cards, and the newest Cisco Any Rate muxponder cards and crossponder cards. These cards are used in terminal, amplifier, and reconfigurable optical add-drop multiplexer (ROADM) node configurations. You configure wavelength-selective switch (WSS) linear and single-module ROADM (SMR) rings. This Optical Technical Training Intermediate course covers 10-gigabit unprotected circuits and 10-gigabit protection using Y-cable, optical channel transport unit-2 (OTU-2), and protection switch module (PSM) cards. Learn more about this NCS 2000 training course below. Course Outline Lesson 1: CTC Operations Lesson 2: MSTP Topologies Lesson 3: Shelf and Card Installation Lesson 4: Fiber jumper installation Lesson 5: Linear Configurations Lesson 6: Node Turn-Up Lesson 7: Optical Channel Network Connection Circuits Lesson 8: Transponder and Optical Channel Client Connection Circuits Lesson 9: Multishelf Lesson 10: MSTP M6 SMR-Based Rings Lesson 11: 10-Gigabit Muxponder and Transponder Cards Lesson 12: 10-Gigabit with Y-Cable Protection Lesson 13: Alternative 10-GB Protection (PSM and OTU-2) Lesson 14: Any Rate Muxponder and Crossponder Lesson 15: Raman Amplifier Lesson 16: 40- and 100-Gigabit Transponder and Muxponder Lesson 17: Troubleshooting Additional course details: Nexus Humans Cisco Optical Technology Intermediate (OPT200) training program is a workshop that presents an invigorating mix of sessions, lessons, and masterclasses meticulously crafted to propel your learning expedition forward. This immersive bootcamp-style experience boasts interactive lectures, hands-on labs, and collaborative hackathons, all strategically designed to fortify fundamental concepts. Guided by seasoned coaches, each session offers priceless insights and practical skills crucial for honing your expertise. Whether you're stepping into the realm of professional skills or a seasoned professional, this comprehensive course ensures you're equipped with the knowledge and prowess necessary for success. While we feel this is the best course for the Cisco Optical Technology Intermediate (OPT200) course and one of our Top 10 we encourage you to read the course outline to make sure it is the right content for you. Additionally, private sessions, closed classes or dedicated events are available both live online and at our training centres in Dublin and London, as well as at your offices anywhere in the UK, Ireland or across EMEA.

Duration 3 Days 18 CPD hours This course is intended for This course is intended for the following technical professionals who need to use advanced features of fiber optics technology: System installers System integrators System administrators Network administrators Solutions designers Overview After taking this course, you should be able to: Perform the ONS 15454 MSTP node turn-up procedure Describe first generation mesh topologies Describe the Optical Channel Network Connection (OCHNC) prerequisite requirements for provisioning circuits in an ONS 15454 MSTP network Describe the ONS MSTP advanced protocols Describe the OCHNC circuit provisioning for Single Module (SM) Reconfigurable Optical Add-Drop Multiplexer (ROADM) rings Describe the Any-Rate Muxponder Crossponder (AR MXP/XP) cards Describe how the Pseudo Command Line can be used to configure muxponder cards Identify the advantages G.709 encapsulation brings to optical transponder cards Install and provision the Any Rate cards Describe the 100-Gbps and 200-Gbps cards Describe the NCS 2000 400-Gbps Xponder line card and how it is configured Describe the SM ROADM (SMR)-based configurations Describe the 10-Gbps transponder and muxponder cards List the 10GE_XP and GE_XP card options Describe ingress policing and basic egress queuing strategies, and implement the customer QoS scheme into the ONS 15454 crossponder network Identify the principles of Ethernet related to the operation of Cisco optical networking products Configure the 10GE_XP/XPE and GE_XP/XPE cards, install Layer 1 circuits, and read the performance counters for Layer 1 Gigabit Ethernet circuits Turn up an encrypted network and test to ensure that information being passed is secure Add a node to an existing DWDM ring Describe problems with interconnecting circuits between rings, the ONS 15454 MSTP 80-channel manual Multiring feature, and hardware components Describe the ONS 15454 MSTP Troubleshooting Guide The Cisco Optical Technology Advanced (OPT300) v2.0 course gives you the skills you need to deploy advanced features of the Cisco© Optical Networking Services (ONS) 15454 Multiservice Transport Platform (MSTP) and Cisco Network Convergence System (NCS) 2000 Series. In this course you?ll learn to how to use the Cisco Transport Planner Design Tool to create network topologies and advanced network topologies. You will learn how to use advanced Dense Wavelength Division Multiplexing (DWDM) features such as G.709 encapsulation, generic framing protocol G.7041, Layer 1 circuits, Quality of Service (QoS), crossponder networks using T1 over Ethernet, and encryption. Course Outline Cisco Transport Planner Design Tool First-Generation Mesh Topologies Ochnc In A Mesh Network Advanced Protocols Any Rate Muxponder And Crossponders 100-Gbps And 200-Gbps Transponders And Muxponders Cisco Ncs 2000 400-Gbps Xponder Line Card Cisco 10G Web Security Essentials (Wse) Network Encryption Card Adding A New Location With Cisco Transport Planner (Ctp) And Cisco Transport Controller (Ctc) Crossponders And Layer 1 Networks Crossponders And Layer 2 Networks Troubleshooting

Duration 3 Days 18 CPD hours This course is intended for This course is designed for technical professionals who need to know how to deploy a Cisco NCS 2000 Series Dense Wavelength-Division Multiplexing (DWDM) network with Flex Spectrum. The primary audience for this course includes: Designers Systems engineers and implementation staff Network operations center personnel Technical support personnel who are involved with the deployment, operations, and maintenance of the Cisco NCS 2000 Series Channel partners and resellers Overview After taking this course, you should be able to: Describe the hardware and components required and used with the Flex Spectrum feature Design optical networks in the Cisco Transport Planner software Install the hardware, including multishelf nodes Perform node turn-up and create circuits using the Cisco Transport Controller software Configure optical networks with multidegree ROADM multishelf nodes Configure optical networks with colorless, contentionless, omnidirectional, and MPO cross-connect advanced features Describe and configure the NCS 2000 400-Gbps Xponder line card Add a node to an existing DWDM ring Describe the NCS 2000 Troubleshooting Guide Use the features and documentation with Transport Controller to perform maintenance, testing, and basic troubleshooting The Cisco NCS2000 Deploying 96-Channel Flex Spectrum (OPT201) v3.0 course shows you how to plan, configure, and control optical networks using the Cisco© Network Convergence System (NCS) 2000 series Flex Spectrum platform.The course teaches you how to design Flex Spectrum networks with multi-degree Reconfigurable Optical Add-Drop Multiplexer (ROADM) multi-shelf nodes using the Cisco Transport Planner (CTP) software. Course Outline DWDM and Flex Spectrum Foundation NCS 2000 Chassis and Cards Design ROADM Networks with CTP Hardware Installation and Multishelf Node Turn-Up and Circuit Creation Advanced Feature Networks and Circuits Testing, Maintenance, and Basic Troubleshooting Spectrum Switched Optical Network