55 EMIS courses

About this Course This 5 full-day course provides a comprehensive understanding of all the commissioning procedures for combined cycle power plants. The Commissioning Management System (CMS) of combined cycle power plants is covered in detail in this course. This includes all the commissioning procedures and documents, purpose of commissioning, responsibilities, system description, organization, working parties, test teams, documentation, testing and commissioning schedules, test reports, safety, plant certification, and plant completion report. The course provides also a thorough understanding of all the commissioning requirements for gas turbines, steam turbines and auxiliaries, generator and auxiliaries, electrical equipment, switchgear equipment, switchgear and transformers. All the stages of the commissioning procedure are covered in-depth in this course. This includes preparation - planning various activities, pre-commissioning checks and tests, typical commissioning schedule, detailed tests and commissioning procedures and instructions for every component in a combined cycle power plant, instrumentation, trial run of the equipment, safety and precautions, commissioning of combined cycle power plant systems, safety rules clearance certificates, procedure for the control and handling of defects, commissioning reports, operational testing, first fire, generator synchronization, performance testing, heat rate testing, emission testing, contract testing, CO2 concentration tests, electrical full-load rejection test, duct burner testing, partial load stability test, and reliability test. This course is a MUST for anyone who is involved in the pre-commissioning or commissioning of any combined cycle power plant equipment because it provides detailed pre-commissioning checks and tests, and detailed tests and commissioning procedures and instructions for every component in a combined cycle power plant. In addition, the seminar provides an in-depth coverage of all preparation, planning activities, commissioning schedules, trial run of each combined cycle power plant equipment, safety and precautions, safety rules clearance certificates, procedures for handling defects, and commissioning reports. Training Objectives Pre-commissioning Checks and Tests, Detailed Tests and Commissioning Procedures and Instructions for Every Equipment in Combined Cycle Power Plants: Gain a thorough understanding of all pre-commissioning checks and tests, and all commissioning procedures and instructions for every equipment in combined cycle power plants Commissioning Management System (CMS) of Combined Cycle Power Plants: Discover the benefits of the CMS of combined cycle power plants including all commissioning procedures and documents, purpose of commissioning, responsibilities, system description, organization, working parties, test teams, documentation, testing and commissioning schedules, test reports, safety, plant certification, and plant completion report Commissioning Procedures and Instructions for Heat Recovery Steam Generators, Air Blow and Steam Blow of Steam and Gas Piping in Combined Cycle Power Plants: Learn about the commissioning procedures and instructions for heat recovery steam generators, chemical cleaning of heat recovery steam generators, air blow and gas blow of steam and gas piping in combined cycle power plants, safety valve setting and soot blowers Commissioning Procedures and Instructions for Gas Turbines and Steam Turbines: Gain a thorough understanding of all the commissioning procedures and instructions for gas and steam turbines and auxiliaries including acid cleaning of oil pipelines, lubrication and governing system (oil flushing and hydraulic testing), jacking oil system, governing system, regenerative system, barring gear, vacuum tightness test, first rolling of turbine and data logging Commissioning Procedures and Instructions for Generator and Auxiliaries: Discover all the commissioning procedures and instructions for generator and auxiliaries including generator, seal oil system, hydrogen gas system, stator water system, rolling and start-up of generators Commissioning Procedures and Instructions for Electrical Equipment: Learn about all the commissioning procedures and instructions for electrical equipment including switchyard equipment, switchgear, transformers and motors Operational Testing, Performance Testing, Heat Rate Testing, Emission Testing of Combine Cycle Power Plants: Gain a thorough understanding of operational testing, first fire, generator synchronization, performance testing, heat rate testing, emission testing, contract testing, CO2 concentration tests, electrical full-load rejection test, duct burner testing, partial load stability test, and reliability test of combined cycle power plants Target Audience Engineers of all disciplines Managers Technicians Maintenance personnel Other technical individuals Training Methods The instructor relies on a highly interactive training method to enhance the learning process. This method ensures that all the delegates gain a complete understanding of all the topics covered. The training environment is highly stimulating, challenging, and effective because the participants will learn by case studies which will allow them to apply the material taught to their own organization. Trainer Your specialist course leader has more than 32 years of practical engineering experience with Ontario Power Generation (OPG), one of the largest electric utility in North America. He was previously involved in research on power generation equipment with Atomic Energy of Canada Limited at their Chalk River and Whiteshell Nuclear Research Laboratories. While working at OPG, he acted as a Training Manager, Engineering Supervisor, System Responsible Engineer and Design Engineer. During the period of time, he worked as a Field Engineer and Design Engineer, he was responsible for the operation, maintenance, diagnostics, and testing of gas turbines, steam turbines, generators, motors, transformers, inverters, valves, pumps, compressors, instrumentation and control systems. Further, his responsibilities included designing, engineering, diagnosing equipment problems and recommending solutions to repair deficiencies and improve system performance, supervising engineers, setting up preventive maintenance programs, writing Operating and Design Manuals, and commissioning new equipment. Later, he worked as the manager of a section dedicated to providing training for the staff at the power stations. The training provided by him covered in detail the various equipment and systems used in power stations. In addition, he has taught courses and seminars to more than four thousand working engineers and professionals around the world, specifically Europe and North America. He has been consistently ranked as 'Excellent' or 'Very Good' by the delegates who attended his seminars and lectures. He written 5 books for working engineers from which 3 have been published by McGraw-Hill, New York. Below is a list of the books authored by him; Power Generation Handbook: Gas Turbines, Steam Power Plants, Co-generation, and Combined Cycles, second edition, (800 pages), McGraw-Hill, New York, October 2011. Electrical Equipment Handbook (600 pages), McGraw-Hill, New York, March 2003. Power Plant Equipment Operation and Maintenance Guide (800 pages), McGraw-Hill, New York, January 2012. Industrial Instrumentation and Modern Control Systems (400 pages), Custom Publishing, University of Toronto, University of Toronto Custom Publishing (1999). Industrial Equipment (600 pages), Custom Publishing, University of Toronto, University of Toronto, University of Toronto Custom Publishing (1999). Furthermore, he has received the following awards: The first 'Excellence in Teaching' award offered by PowerEdge, Singapore, in December 2016 The first 'Excellence in Teaching' award offered by the Professional Development Center at University of Toronto (May, 1996). The 'Excellence in Teaching Award' in April 2007 offered by TUV Akademie (TUV Akademie is one of the largest Professional Development centre in world, it is based in Germany and the United Arab Emirates, and provides engineering training to engineers and managers across Europe and the Middle East). Awarded graduation 'With Distinction' from Dalhousie University when completed Bachelor of Engineering degree (1983). Lastly, he was awarded his Bachelor of Engineering Degree 'with distinction' from Dalhousie University, Halifax, Nova Scotia, Canada. He also received a Master of Applied Science in Engineering (M.A.Sc.) from the University of Ottawa, Canada. He is also a member of the Association of Professional Engineers in the province of Ontario, Canada. POST TRAINING COACHING SUPPORT (OPTIONAL) To further optimise your learning experience from our courses, we also offer individualized 'One to One' coaching support for 2 hours post training. We can help improve your competence in your chosen area of interest, based on your learning needs and available hours. This is a great opportunity to improve your capability and confidence in a particular area of expertise. It will be delivered over a secure video conference call by one of our senior trainers. They will work with you to create a tailor-made coaching program that will help you achieve your goals faster. Request for further information post training support and fees applicable Accreditions And Affliations

A thorough account of the UK and European legal framework and its requirements as regards managing environmental performance. This course will help staff to understand: The framework of UK and European legislation and its enforcement The principal features of the legislation as they apply to your organisation's activity/product/service The benefit of having an Environmental Management System such as ISO 14001 How their own actions and decisions can either expose or protect the organisation in relation to its legal obligations 1 Introduction and objectives 2 Introduction to environmental law and enforcement Sources of law (European and UK) Structure and enforcement Key legislation 3 Integrated Pollution Prevention and Control (IPPC) and Local Air Pollution and Control (LAPC) Pollution and Prevention Control Act 1999 EC Directives on PPC The meaning of BAT Transitional provisions Fit and proper persons Control of emissions to air National Air Quality Strategy 4 Packaging and producer responsibilities Who, what and how The Producer Responsibility Obligations (Packaging Waste) Regulations Obligations and exemptions Registration Recycling and recovery obligations Records Duties of the Environment Agency Offences Developments 5 Waste management National Waste Strategy Waste minimisation (re-use/recycling) Waste definition Disposal and recovery Controlled waste management Hazardous waste management 6 Proposed Legislation and EC Directives EU Commission's waste and resources strategies Implementation of ELV (End of Life Vehicles) Directive WEEE (Waste Electrical and Electronic Equipment) Directive transposition into UK legislation Other producer responsibility initiatives Other proposals from the EU 7 Conclusion Open forum Summary Close

This course follows the Institute of Occupational Safety and Health's syllabus. A one-day programme, it is suitable for all people at all levels in the workplace and gives a basic introduction to the principles of environmental management. On successful completion of the course, participants will be able to: Understand the terms 'environment' and 'pollution' Understand the terms 'hazard' and 'risk' related to the environment Better appreciate environmental issues generally, and specifically in respect of their organisation Identify hazards to the environment from working practices Outline the procedures/controls necessary to prevent damage to the environment 1 What is the environment? - putting the environment in context Key environmental issues and how we contribute Definition of the environment 2 Working with the environment What is pollution? Sources, receptors and pathways Environmental consequences workshop - identifying the environmental consequences of our working practices Environmental risk assessment Effective control mechanisms 3 Protecting the environment - Environmental Management Systems What is an Environmental Management System (EMS)? What are the benefits of having an EMS? EMS structure and models Identifying what elements of EMS your company has and how they work Roles and responsibilities 4 Choice of module Option 1: Organisation-specific moduleThis module can be used to introduce environmental concepts that are specific to your activities and operations, and will be compiled through discussion with your organisation Option 2: Environmental best practiceIf no organisation-specific module is required, or if participants from a number of organisations attend, generic operational environmental best practices can be covered instead. Areas covered include waste management, fuel storage and use, hazardous materials, emissions to air and water and environmental incidents

The importance of building services to the success of an organisation has never been greater and continues to grow. Developers and occupiers are becoming more aware of the contribution that building services make to the well being of occupants and hence their perception of the quality of the working environment. Those involved with the design, construction, maintenance and operation will increasingly be required to deliver building services that demonstrable contribution to the occupier's business. Energy efficiency, carbon management and occupant satisfaction depend substantially on the way building services are designed, managed and operated. To optimise these aspects, an informed strategic approach is essential. Tried and tested techniques and processes are available that, when applied holistically, will deliver substantial benefits. This course reviews best practice in the area and inspires participants to ensure that building services perform at their optimal level. To provide a better understanding of how building services can be designed, managed and operated to: Maximise occupant comfort, satisfaction and wellbeing Add value and contribute to the success of the business of the occupier Improve health safety Reduce operating cost, energy use, carbon emissions and environmental impact Optimise cost and value Provide strategies for continuous improvement and sustainable operation 1 Building services fundamentals The function of services in commercial buildings and their importance to the core business 2 Techniques and processes for optimising cost and value Programmed operation evaluation Continuous commissioning Lifetime product management Performance-based service Energy efficiency and the scope for environmental improvement 3 Making the business case and preparing the strategy Motivating decision-makers Empowering those who have to deliver the results Managing business risk 4 Strategy implementation and monitoring results Ensuring that rich and robust feedback is available to support continuous improvement and strategy enhancementWhen to get feedbackWhyHowWhat to do with it 5 Case histories and 'air time' Sharing experience and addressing specific issues of interest to participants Course review Close

Relocating to a new home in London can be both exciting and challenging. The city’s fast-paced lifestyle, narrow streets, and busy traffic demand precision and expertise during a move. That’s why partnering with a reliable house removal company in London can make all the difference. With professional support, you can focus on enjoying your new home without the stress of logistics. Why Choose a Professional London Removals Company? A trusted London removals company offers services that simplify the moving process, ensuring that your belongings are transported safely and efficiently. Here are some key benefits: Expert Handling: Professional movers have the skills to handle fragile, heavy, or valuable items with care. Efficient Packing: Save time and effort with expert packing services that protect your possessions during transit. Stress Reduction: Let professionals handle the heavy lifting while you focus on settling into your new space. Tailored Services: Choose from a range of options, such as full-service moves, storage solutions, or specialty item transport. By hiring a house removal company in London, you ensure a seamless moving experience, tailored to your unique needs. Comprehensive Services for House Removals London-based removal companies typically offer a wide array of services to accommodate different moving requirements. These include: Full-Service Removals A full-service move handles everything from packing and transportation to unpacking at your new home. Packing and Unpacking Services Movers use durable packing materials to safeguard your belongings, including fragile items like glassware or electronics. Furniture Assembly and Disassembly Large pieces of furniture are dismantled for easier transport and reassembled upon arrival. Temporary Storage Options Need to store your items for a short time? Many companies provide secure storage facilities. Specialized Item Transport For pianos, artwork, or antiques, specialized services ensure that your valuable possessions are handled with utmost care. How to Choose the Right House Removal Company in London Finding the best removal company involves considering a few critical factors: Reputation: Look for customer reviews and testimonials to gauge reliability and service quality. Experience: A seasoned London removals company will know how to navigate the city’s challenges effectively. Insurance Coverage: Ensure the company offers insurance for your items during transit. Transparent Pricing: Request a detailed quote to avoid hidden costs or unexpected charges. Flexibility: Choose a company that accommodates your moving schedule and specific needs. Why London Removals Require Local Expertise Moving in London presents unique challenges, such as limited parking, restricted access areas, and narrow roads. Experienced house removal companies in London understand these obstacles and provide solutions: Navigating Traffic: Knowledge of local traffic patterns ensures timely arrivals and departures. Securing Permits: Professionals handle parking permits or restricted access requirements for specific areas. Efficient Route Planning: Local expertise helps avoid delays by selecting the best routes. Tips to Prepare for Your Move Even with professional help, some preparation on your part can make the process smoother: Declutter Your Home Before packing, decide what items you no longer need and donate, sell, or recycle them. Label Your Boxes Mark each box with its contents and destination room to simplify unpacking. Pack an Essentials Bag Include items you’ll need immediately after moving, like toiletries, a change of clothes, and important documents. Notify Utilities and Services Update your address with utility providers, banks, and subscription services before moving day. Communicate with Your Movers Share specific instructions or concerns with your London removals company to ensure everything goes smoothly. Eco-Friendly Moving Options Sustainability is becoming an essential consideration for many movers. Some London removal companies offer eco-friendly services, such as: Using biodegradable packing materials Reducing vehicle emissions with optimized routes Recycling or donating unwanted items The Value of Professional Help Moving is often considered one of life’s most stressful events, but it doesn’t have to be. With the help of a reputable house removal company in London, you can enjoy a hassle-free experience from start to finish. Whether it’s packing, transporting, or unpacking, professionals handle every detail with care and precision. If you’re planning a move, consider a trusted London removals company to make your transition as smooth as possible. With their expertise, you’ll be settled into your new home in no time, ready to embrace the next chapter of your life.