33 Courses in Liverpool delivered Online

About this Training Course This course will begin with a presentation of topics to familiarize Process and Instrumentation Engineers with procedures and practices involved in the choice of sensors related to the measurement of temperature, pressure, level and flow in relation to single-phase flows. It will provide guidance on the optimum commercially available devices through a detailed comparison of their relative merits. At the heart of this course is sensor calibration which is a crucial element for these topics. The course will also examine the various types of flow control valve, including Globe, Slide, Needle, Eccentric plug and Ball valves and their characteristics in industrial application, while focusing on the problems of Cavitation and Flashing and methods to minimise or eradicate these issues. With the use of examples, industry case studies and a wide range of videos, this course will also cover all aspects of proportional (P), derivative (D) and integral (I) control. In particular, it will address the advantages and disadvantages of PI and PID control. It will also describe Cascade, Feed forward, Split Range, Override and Ratio Control techniques. Training Objectives By attending this course, participants will acquire the following knowledge and skills: Apply an in-depth knowledge to the measurement of temperature, pressure, level and flow as well as to the fluid mechanics of pipe flows Assess the advantages and disadvantages of the major flowmeter types including the differential pressure, rotary positive displacement, rotary-inferential, electromagnetic, ultrasonic and Coriolis mass flowmeters to determine the optimum choice for a given application Make a considered judgement of the choice of fluid level measurement devices Understand the various types of flow calibration, metering systems and provers Carry out tank measurement and tank calibration methods and to calculate net sellable quantities Discuss valve characteristics & trim selection and illustrate the process of control valve sizing Explain the terms Open and Closed loop Define Process Variable, Measured Variable, Set Point and Error Define Direct and Reverse controller actions Explain the terms Process Lag, Measurement Lag, Transmission Lag, and Response Lag and their effect on controllability Explain ON/ OFF Control and the inherent disadvantages Explain Proportional Control, Offset, Gain and Proportional Band and the advantages and disadvantages of Proportional only control Explain the fundamentals and operation principles of Integral (I) Action and the disadvantages of proportional plus integral control Explain the fundamentals and operation principles of Derivative (D) Action in conjunction with P action Describe the operating principles of a PID Controller and explain the applications and advantages of PID control Describe Cascade, Forward, Split Range and Ratio Control operation principles Target Audience This course will benefit instrumentation, inspection, control, custody metering and process engineers and other technical staff. It is also suitable for piping engineers, pipelines engineers, mechanical engineers, operations engineers, maintenance engineers, plant/field supervisors and foremen and loss control coordinators. Trainer Your expert course leader is a Senior Mechanical & Instrumentation Engineer (UK, B. Sc., M.Eng., Ph D) with over 45 years of industrial experience in Process Control & Instrumentation, Pumps, Compressors, Turbines and Control Valve Technology. He is currently a Senior Independent Consultant to various petrochemical industries in the UK, USA, Oman, Kuwait and KSA where he provides consultancy services on both the application and operational constraints of process equipment in the oil & gas industries. During his early career, he held key positions in Rolls Royce (UK) where he was involved in the design of turbine blading for jet engines, subject to pre-specified distributions of pressure. During this period and since, he has also been closely involved in various aspects of Turbomachinery, Thermodynamics and Fluid Mechanics where he has become a recognised authority in these areas. Later, he joined the academic staff of University of Liverpool in the UK as a Professor in Mechanical Engineering Courses. A substantial part of his work has been concerned with detailed aspects of Flowmetering - both of single & multiphase flows. He has supervised doctoral research students in this area in collaboration with various European flowmeter manufacturers. He joined Haward Technology Middle East in 2002 and was later appointed as European Manager (a post which has since lapsed) and has delivered over 150 training courses in Flowmeasurement (single- and multi-phase), Control, Heat Exchangers, Pumps, Turbines, Compressors, Valve and Valve Selection as well as other topics throughout the UK, USA, Oman and Kuwait. During the last two years, he has delivered courses with other training companies operating in the Far and Middle East. He has published about 150 papers in various Engineering Journals and International Conferences and has contributed to textbooks on the topics listed above. POST TRAINING COACHING SUPPORT (OPTIONAL) To further optimise your learning experience from our courses, we also offer individualized 'One to One' coaching support for 2 hours post training. We can help improve your competence in your chosen area of interest, based on your learning needs and available hours. This is a great opportunity to improve your capability and confidence in a particular area of expertise. It will be delivered over a secure video conference call by one of our senior trainers. They will work with you to create a tailor-made coaching program that will help you achieve your goals faster. Request for further information post training support and fees applicable Accreditions And Affliations

Advance Cardiac Rehabilitation Physiotherapy Protocol Aims To The care of patients with heart failure costs the United States $32 billion annually. The body of evidence supporting exercise therapy for this patient population is growing. This course will provide a broad overview of heart failure pathophysiology including an explanation of the difference between diastolic and systolic heart failure. A primary focus of the course will be to highlight the common findings on a physical therapy examination seen in patients with heart failure. The course will conclude with the application of the literature to prescribing exercise in this patient population that can be applied across the continuum of care. Attendees will learn practical applications of the patient examination and current evidence that can be applied immediately to their clinical setting. The aim of the cardiac rehabilitation physiotherapy as follow; Pathophysiology of heart failure Difference between diastolic and systolic heart failure Cardio Physical Therapy Examination Cardio Physical Therapy intervention Criteria for terminating physiotherapy intervention in cardiac patient Learning Objective  Explain the pathophysiology of heart failure. Recognize the difference between diastolic and systolic heart failure. Describe the clinical decision-making involved in the physical therapist examination. Create evidence-based exercise prescriptions for patients with heart failure throughout the stages of the disease. Recognize indications for termination of exercise. Who Should Enroll Physiotherapist Occupational Therapist Sports Physiologist Athletic Trainer Nurses CPD Credit Hours 2 Hours Resources 1-Month Access to Learning Resources Downloadable Course Material CPD Certificate Author Presenter: Jackie Mulgrew, PT, DPT, CCS Jackie Mulgrew PT, DPT, CCS is a graduate of Liverpool University, England. Jackie brings 23 years of acute care experience to this course, having worked in major acute care hospitals in England and the USA. Currently employed at Massachusetts General Hospital as a Cardiovascular and Pulmonary Board Certified Clinical Specialist, she specializes in the care of cardiac medical and surgical patients and is responsible for the clinical and professional development of the physical therapy staff. Jackie has facilitated cardiopulmonary tutorial sessions at Simmons College and the Institute for Health Professions in Boston and has lectured for Boston University’s graduate program in physical therapy. For the last 6 years, Jackie has taught acute care physical therapy around the country. Jackie is the author of Circulatory Assist Devices in the Acute Care Handbook and her clinical interests include heart failure, mechanical circulatory support, and exercise testing.

This concise and comprehensive course takes you through the basic and advanced topics of Ansible, explaining all the concepts clearly and thoroughly. You will not only master the concepts but also learn how to use Ansible with cloud services and containers.

A popular 6-week Mindfulness Meditation and Dynamic Breathing course that provides participants with tools to support them in an increasingly challenging world.

Level 3 Award in Education and Training AET Course is designed to give people the knowledge and confidence to teach adult in any specialty subject area. Learn More Academy has been delivering the Level 3 (12 Credits) Award in Education and Training AET formerly known (PTLLS) qualification. Level 3 AET course is designed to contribute towards the knowledge and understanding for Further Education National Training Organisation (FENTO) or the Employment National Training Organisation (EMPNTO) occupational standards in the United Kingdom.

PTLLS is a teacher training qualification for those new to teaching / training industry or wanting to start out as associate teachers, or currently teaching. Learn More Academy has been delivering the Level 3 Preparing to Teach in the Lifelong Learning Sector (PTLLS) or newly branded AET course. Level 3 Award in Education and Training (AET) course is designed to contribute towards the knowledge and understanding for Further Education National Training Organisation (FENTO) or the Employment National Training Organisation (EMPNTO) occupational standards in the United Kingdom. This course is designed for anyone wishing to enter in the adult training and teaching industry in this country and even some other country too.

CAVA is a combined of assessment of occupational competence in the work environment, and the assessment of vocational skills, knowledge and understanding. Level 3: Certificate in Assessing Vocational Achievement (RQF) course is suitable for people who assess vocational skills, knowledge and understanding other than in the work environment (e.g. a workshop, classroom or other training environment).

Level 4 Internal Quality Assurance IQA qualification is previously known as V1 or Verifier award in the is a 12 credit and 90 guided learning hour. It does not only relate to the training industry, it can be quality assurance within any field and sector. If you have been looking after the quality of training or have been responsible for making sure employees work according to procedures and practice within your work place, you can transfer your experience and get qualified as an Internal Quality Assurer.

Level 3 Assessor course formerly known as A1 TAQA course. Learn More Academy provides all level of Assessor courses in England, Wales and Scotland. This courses was formerly known as TAQA course and this qualification is intended for those who wish to gain an understanding of the principles and practices of assessment without any requirement to practice as assessors.

Level 4 CET course is a first stage teaching qualification which has a teaching/training practice requirement. This qualification designed for those working or wishing to work as teachers/trainers. Formerly this courses was known as CTLLS. Candidates who successfully complete this qualification will have a fundamental understanding of the roles and responsibilities of a teacher/trainer in relation to legislation, equality, diversity, inclusivity and meeting the needs of learners. They will be able to use initial and diagnostic assessments and plan and deliver inclusive teaching and learning. They will also be able to assess learning and use appropriate resources to support effective learning.