250 Construction courses in Cardiff

Using an excavator as a crane is a common practice in certain construction and lifting operations. Using the digger as a crane requires appropriate training and skills However, it’s important to note that excavators are primarily designed for digging and earthmoving, not lifting. Using an Excavator as a Crane involves some inherent risks, and it’s crucial to follow safety guidelines and manufacturer recommendations. To book the NPORS Excavator as a Crane training or test please contact us to schedule your Training Here are some general considerations and steps you might take when using an excavator as a crane: 1. Check Manufacturer Guidelines: Always consult the manufacturer’s guidelines and specifications for the specific excavator model you are using. Manufacturers provide load charts and other essential information to ensure safe operation. 2. Understand Load Capacities: Know the lifting capacities of your excavator at various boom lengths and angles. Exceeding these capacities can lead to instability and accidents. 3. Use Proper Attachments: If your excavator is equipped with a lifting attachment, make sure it is designed and rated for lifting operations. Using inappropriate attachments can compromise safety. 4. Stabilise the Excavator: Ensure that the excavator is on stable ground. Extend the outriggers or stabilisers to provide additional support and prevent tipping. 5. Inspect the Excavator: Regularly inspect the excavator for any signs of wear, damage, or malfunction. Pay particular attention to the boom, hydraulics, and other critical components. 6. Position the Excavator: Position the excavator in a way that allows for a stable lifting operation. Avoid working on slopes or uneven surfaces. 7. Rigging and Lifting Techniques: Use proper rigging techniques, and ensure that the load is properly secured. Lift the load smoothly and avoid sudden movements. 8. Maintain Clear Communication: Establish clear communication between the operator and any ground personnel involved in the lifting operation. Use hand signals or radios to coordinate movements. 9. Avoid Exceeding Reach Limits: Do not exceed the excavator’s reach limits. Lifting loads beyond the recommended reach can lead to instability. 10. Training and Certification: Ensure that operators are properly trained and certified for lifting operations. Holding the NPORS Excavator As A Crane bolt on is essential for lifting operations Operating an excavator as a crane requires specific skills and knowledge. 11. Weather Conditions: Consider weather conditions, especially wind speeds, as they can affect the stability of the excavator during lifting operations. Always prioritise safety when using equipment for tasks it wasn’t originally designed for. If the lifting requirements are frequent or extensive, it may be more appropriate to use a dedicated crane with the necessary capacity and features. Remember, safety is paramount in any construction or lifting operation. Frequently Asked Questions 1. What is Excavator As A Crane Training, and why is it necessary? Excavator As A Crane Training provides individuals with the skills and knowledge required to safely and effectively use excavators for lifting operations. Although excavators are primarily designed for digging and earthmoving, this training ensures operators can perform lifting tasks safely, minimizing risks and accidents on job sites. 2. Who should undergo Excavator As A Crane Training? This training is essential for anyone involved in using excavators for lifting operations, including machine operators, construction workers, and site supervisors. Proper training ensures that individuals understand equipment operation procedures, load capacities, and safety protocols. 3. What topics are covered in Excavator As A Crane Training programs? Training programs cover a range of topics, including: Manufacturer guidelines and load charts Understanding load capacities at various boom lengths and angles Proper use of lifting attachments Excavator stabilization techniques Rigging and lifting techniques Positioning and communication strategies Safety procedures and weather considerations Regular inspection and maintenance of equipment 4. Is Excavator As A Crane Training mandatory in certain industries? While not legally mandated in all areas, many employers in the construction and lifting industries require operators to undergo training as part of their occupational health and safety policies. Compliance with excavator as a crane training requirements helps prevent accidents and ensures regulatory compliance. 5. Where can I find reputable Excavator As A Crane Training courses? Reputable Excavator As A Crane Training Courses are offered by various institutions, including industry associations, equipment manufacturers, and specialized training providers like Vally Plant Training. It is important to choose a program that offers accredited certification and covers relevant industry standards and best practices.

This course is designed to provide training for those undertaking the role of temporary works...

This course is designed to assist those on site who have responsibility for managing all forms of...

Overview of Telehandler Training Course Telehandler Training or Telehandler Courses is an essential program designed to equip operators with the necessary skills and knowledge to safely and efficiently operate telehandlers. These versatile machines, commonly used in agriculture, construction, and warehousing, require precise handling due to their complex controls and varied load capacities. Our Telehandler Courses will help you achieve your goal to be a successful Telehandler Operator. The importance of comprehensive telehandler training cannot be overstated. It ensures that operators are well-versed in both the theoretical and practical aspects of handling these machines, significantly reducing the risk of accidents and injuries on the job. Moreover, proper Telehandler training aids in maximising the operational efficiency of telehandlers, which can contribute to the timely completion of projects and the effective management of resources. In various industries, telehandlers play a critical role in lifting and transporting heavy materials over obstacles and uneven terrain, making the Telehandler course crucial for anyone involved in operations that require heavy lifting and material handling. The Telehandler courses covers a range of topics, including safety regulations, operational techniques, maintenance basics, and troubleshooting common issues, ensuring that all participants are prepared to handle the demands of operating a telehandler in any setting. Booking the Telehandler Training couldn’t be easier. Book Now

This 1/2 day course gives delegates a better understanding of safety and the assessment of risk.

This course provides participants with a comprehensive understanding of the requirements of the CDM Regulations 2015 and how these should be implemented in practice. The Regulations are put in context with other key health and safety legislation. The programme sets out clearly the roles and responsibilities of the principal duty holders and explores with the participants how these roles may vary on different types of project and procurement routes. The programme examines the content and appropriate level of information that should be included in the Pre-Construction Information and the Construction Phase Plan. The trainer will discuss best practice in implementing CDM through the new 2015 Regulations and Guidance. This course is essential for anyone who is involved in the procurement, planning, design or implementation of construction work. The course will provide you with: An overview of construction health and safety law, liability and enforcement A detailed understanding of the 2015 CDM Regulations and the part they play with other key legislation An explanation of the roles and responsibilities of all duty holders and the requirements for the CDM documentation Clear advice on current best practice for complying with the principles of the CDM Regulations and the changes introduced by the 2015 Regulations An understanding of how risk assessment should be applied practically throughout the design and how this responsibility is then transferred to contractors 1 Introduction Why manage health and safety? The costs of accidents Construction industry statistics Why CDM? Health and safety culture in the construction industry 2 Overview of health and safety law and liabilities Criminal and civil law Liability Enforcement and prosecution Compliance - how far do we go? Statutory duties 3 Health and safety law in construction Framework of relevant legislation Health and Safety at Work etc Act 1974 Management of Health and Safety at Work Regulations 1999 Construction (Design and Management) Regulations 2015 Who is responsible for the risks created by construction work? Shared workplaces/shared responsibilities Control of contractors - importance of contract law 4 Construction (Design and Management) Regulations 2015 Scope - What is construction? Application - When do they apply? The CDM Management System Duty holders (Client, Domestic Client, Designer, Principal Designer, Principal Contractor, Contractor) Documents (HSE Notification, Pre-Construction Information, Construction Phase Health & Safety Plan, H&S File) Management process The 2015 Guidance 5 Best practice - key issues in the CDM process The client and client management arrangements Competence and resource under CDM 2015 The role of the Principal Designer in practice Design risk assessment and the role of the Designer The CDM Documents (PCI, PCI Pack, Plan and File) Construction health, safety and welfare Making CDM work in practice 6 Questions, discussion and review

This course provides participants with a comprehensive understanding of the requirements of the CDM Regulations 2015 and how these should be implemented in practice. The Regulations are put in context with other key health and safety legislation. The programme sets out clearly the roles and responsibilities of the principal duty holders and explores with the participants how these roles may vary on different types of project and procurement routes. The programme examines the content and appropriate level of information that should be included in the Pre-Construction Information and the Construction Phase Plan. The trainer will discuss best practice in implementing CDM through the new 2015 Regulations and Guidance. This course is essential for anyone who is involved in the procurement, planning, design or implementation of construction work. The course will provide you with: An overview of construction health and safety law, liability and enforcement A detailed understanding of the 2015 CDM Regulations and the part they play with other key legislation An explanation of the roles and responsibilities of all duty holders and the requirements for the CDM documentation Clear advice on current best practice for complying with the principles of the CDM Regulations and the changes introduced by the 2015 Regulations An understanding of how risk assessment should be applied practically throughout the design and how this responsibility is then transferred to contractors 1 Introduction Why manage health and safety? The costs of accidents Construction industry statistics Why CDM? Health and safety culture in the construction industry 2 Overview of health and safety law and liabilities Criminal and civil law Liability Enforcement and prosecution Compliance - how far do we go? Statutory duties 3 Health and safety law in construction Framework of relevant legislation Health and Safety at Work etc Act 1974 Management of Health and Safety at Work Regulations 1999 Construction (Design and Management) Regulations 2015 Who is responsible for the risks created by construction work? Shared workplaces/shared responsibilities Control of contractors - importance of contract law 4 Construction (Design and Management) Regulations 2015 Scope - What is construction? Application - When do they apply? The CDM Management System Duty holders (Client, Domestic Client, Designer, Principal Designer, Principal Contractor, Contractor) Documents (HSE Notification, Pre-Construction Information, Construction Phase Health & Safety Plan, H&S File) Management process The 2015 Guidance 5 Best practice - key issues in the CDM process The client and client management arrangements Competence and resource under CDM 2015 The role of the Principal Designer in practice Design risk assessment and the role of the Designer The CDM Documents (PCI, PCI Pack, Plan and File) Construction health, safety and welfare Making CDM work in practice 6 Questions, discussion and review

This course is designed to provide delegates that intend to work as part of a confined space rescue team with an introduction to planning and executing casualty rescue procedures and the equipment which may be required. This is intended for delegates who already hold a high risk (full Breathing apparatus) qualification such as our CS2. Note: A pre-requisite qualification is required to complete this course. The ESS CS2 course (https://www.vp-ess.com/training/confined-spaces/cs2-(high-risk)-confined-space-entry-full-breathing-apparatus,-self-rescue-and-ba-control/) must have been completed within 6 months as a pre-requisite for this CS3 course. Book via our website @ https://www.vp-ess.com/training/confined-spaces/cs3-introduction-to-working-as-a-member-of-a-confined-space-rescue-team/ or via email at: esstrainingsales@vpplc.com or phone on: 0800 000 346

City & Guilds Level 3 Award in Working as Member of a Rescue Team - 6160-08 - The course includes preparing to carry out emergency activities, entering and exiting confined spaces safely, using emergency equipment, casualty recovery and handling devices in accordance with manufacturers’ specifications, rescuing and recovering casualties, following procedures and working safely. Note: A pre-requisite qualification is required to complete this course. Delegates must hold a valid City & Guilds 6160-03 qualification. Book via our website @ https://www.vp-ess.com/training/confined-spaces/6160-08-city-and-guilds-level-3-award-in-working-as-member-of-a-rescue-team/ or via email at: esstrainingsales@vpplc.com or phone on: 0800 000 346

CS2 - (High Risk) Confined Space Entry, Full Breathing Apparatus, Self-Rescue and BA Control - This course is designed to provide delegates that need to enter confined spaces with an in-depth understanding of the requirements of the law, associated regulations and safe systems of work. This course covers access, egress and safe working practices in confined spaces. Book via our website @ https://www.vp-ess.com/training/confined-spaces/cs2-(high-risk)-confined-space-entry-full-breathing-apparatus,-self-rescue-and-ba-control/ or via email at: esstrainingsales@vpplc.com or phone on: 0800 000 346