18 Courses in Liverpool

About this Training Course This course will begin with a presentation of topics to familiarize Process and Instrumentation Engineers with procedures and practices involved in the choice of sensors related to the measurement of temperature, pressure, level and flow in relation to single-phase flows. It will provide guidance on the optimum commercially available devices through a detailed comparison of their relative merits. At the heart of this course is sensor calibration which is a crucial element for these topics. The course will also examine the various types of flow control valve, including Globe, Slide, Needle, Eccentric plug and Ball valves and their characteristics in industrial application, while focusing on the problems of Cavitation and Flashing and methods to minimise or eradicate these issues. With the use of examples, industry case studies and a wide range of videos, this course will also cover all aspects of proportional (P), derivative (D) and integral (I) control. In particular, it will address the advantages and disadvantages of PI and PID control. It will also describe Cascade, Feed forward, Split Range, Override and Ratio Control techniques. Training Objectives By attending this course, participants will acquire the following knowledge and skills: Apply an in-depth knowledge to the measurement of temperature, pressure, level and flow as well as to the fluid mechanics of pipe flows Assess the advantages and disadvantages of the major flowmeter types including the differential pressure, rotary positive displacement, rotary-inferential, electromagnetic, ultrasonic and Coriolis mass flowmeters to determine the optimum choice for a given application Make a considered judgement of the choice of fluid level measurement devices Understand the various types of flow calibration, metering systems and provers Carry out tank measurement and tank calibration methods and to calculate net sellable quantities Discuss valve characteristics & trim selection and illustrate the process of control valve sizing Explain the terms Open and Closed loop Define Process Variable, Measured Variable, Set Point and Error Define Direct and Reverse controller actions Explain the terms Process Lag, Measurement Lag, Transmission Lag, and Response Lag and their effect on controllability Explain ON/ OFF Control and the inherent disadvantages Explain Proportional Control, Offset, Gain and Proportional Band and the advantages and disadvantages of Proportional only control Explain the fundamentals and operation principles of Integral (I) Action and the disadvantages of proportional plus integral control Explain the fundamentals and operation principles of Derivative (D) Action in conjunction with P action Describe the operating principles of a PID Controller and explain the applications and advantages of PID control Describe Cascade, Forward, Split Range and Ratio Control operation principles Target Audience This course will benefit instrumentation, inspection, control, custody metering and process engineers and other technical staff. It is also suitable for piping engineers, pipelines engineers, mechanical engineers, operations engineers, maintenance engineers, plant/field supervisors and foremen and loss control coordinators. Trainer Your expert course leader is a Senior Mechanical & Instrumentation Engineer (UK, B. Sc., M.Eng., Ph D) with over 45 years of industrial experience in Process Control & Instrumentation, Pumps, Compressors, Turbines and Control Valve Technology. He is currently a Senior Independent Consultant to various petrochemical industries in the UK, USA, Oman, Kuwait and KSA where he provides consultancy services on both the application and operational constraints of process equipment in the oil & gas industries. During his early career, he held key positions in Rolls Royce (UK) where he was involved in the design of turbine blading for jet engines, subject to pre-specified distributions of pressure. During this period and since, he has also been closely involved in various aspects of Turbomachinery, Thermodynamics and Fluid Mechanics where he has become a recognised authority in these areas. Later, he joined the academic staff of University of Liverpool in the UK as a Professor in Mechanical Engineering Courses. A substantial part of his work has been concerned with detailed aspects of Flowmetering - both of single & multiphase flows. He has supervised doctoral research students in this area in collaboration with various European flowmeter manufacturers. He joined Haward Technology Middle East in 2002 and was later appointed as European Manager (a post which has since lapsed) and has delivered over 150 training courses in Flowmeasurement (single- and multi-phase), Control, Heat Exchangers, Pumps, Turbines, Compressors, Valve and Valve Selection as well as other topics throughout the UK, USA, Oman and Kuwait. During the last two years, he has delivered courses with other training companies operating in the Far and Middle East. He has published about 150 papers in various Engineering Journals and International Conferences and has contributed to textbooks on the topics listed above. POST TRAINING COACHING SUPPORT (OPTIONAL) To further optimise your learning experience from our courses, we also offer individualized 'One to One' coaching support for 2 hours post training. We can help improve your competence in your chosen area of interest, based on your learning needs and available hours. This is a great opportunity to improve your capability and confidence in a particular area of expertise. It will be delivered over a secure video conference call by one of our senior trainers. They will work with you to create a tailor-made coaching program that will help you achieve your goals faster. Request for further information post training support and fees applicable Accreditions And Affliations

IPAF training is the most widely recognised standard for Mobile Elevated Work Platform operators. These are commonly known as MEWP’s or Scissor Lifts and Cherry Pickers. MHA Training is a fully approved and registered IPAF member and we can deliver a wide range of courses. This can be done at our training centre in Warrington or On-Site at customer premises Nationwide. The International Powered Access Federation (IPAF) promotes the safe and effective use of powered access worldwide. Set up in 1983, IPAF is a non-profit organisation that represents the interests of member training companies. Over the years, IPAF has played a key role in promoting many of the design safety and testing procedures that are now established in the powered access industry. Companies such as MHA Training in Warrington are responsible for training for over 90,000 operators each year. Those who successfully complete their training at our centre in Warrington, or out On-Site nationwide are awarded the PAL Smart card. The (Powered Access Licence) is the most widely held and recognised qualification for mobile platform operators. The PAL Smart card is valid for five years and shows the machine categories that an operator has been trained on. It also features the holders photo and signature, and can be verified on their website. IPAF itself does not provide any training, it is provided by approved quality training centres like MHA Training. Approved training centres are regularly audited by IPAF, which ensures the highest standards are consistently met. Class sizes are kept small and courses generally last 1-2 days and are a mixture of theory and practical. To ensure success candidates must then undergo a 30 question multiple choice paper and a practical test. Course material is available in many languages and training centre’s receive regular updates. MHA Training was established in 2008 based at our training centre in Warrington, Cheshire. We provide an array of services On-Site also for clients around the North West in areas such as Manchester, Liverpool, Widnes, St. Helens, Runcorn, Wigan, Preston and Leeds. Over the years we have expanded and have instructors available Nationwide. IPAF E-Learning. IPAF’s new E-learning module is part of its full training programme for mobile elevating work platforms (MEWPs). The E-learning module delivers flexibility and interactive tools, with the same emphasis on practical training. Together with supervised written and practical testing of operator skills. E-learning can lead to a PAL Card (Powered Access Licence) which proves that the operator has successfully completed the training and is able to operate MEWP’s safely. Benefits: Flexible. Trainees complete the theory part anytime, anywhere, on any device, at their own pace. Interactive. Engages trainees with games, quizzes, videos and simulations. Operator E-learning does not replace practical training. Trainees who complete the online session must still pass a supervised theory test with an IPAF centre like MHA training. Also must successfully complete a minimum half-day of practical training and testing before being issued a PAL Card as proof of successfully completed operator training. Training Courses Available: Operators. Demonstrators. Static Boom (1b). Mobile Vertical (3a). Mobile Boom (3b). Push Around Vertical (PAV). Other courses: Harness Use and Inspection (H).

Carried out by qualified instructors, the Manual Handling Training course is designed to cover a number of Manual Handling topics. It will enable the candidate on completion to recognise a manual handling problem. It will give them the tools to be able to initiate a risk assessment and lift or carry in a safe manner. We can deliver these courses in-house or to gain Qualsafe certification. Fully Qualified and Highly Experienced Instructors. Half day course (2-3 Hours). Our courses include the following subject areas: The requirements of the Manual Handling Operations Regulations. The legal requirements to provide Manual Handling Training. Principles of good movement. The anatomy of the spine. Manual Handling related injuries. Mechanics of incorrect and correct manual handling techniques. Practical exercises. Principles of manual handling techniques will include: The task. The load. The working environment. The individual capability. Practical applications of lifting, pushing, pulling and carrying. Risk Assessment and its practical application. There is a Maximum of up to 20 Candidates per Manual Handling training course, however we can run two courses per day with one manual handling instructor. We also have more manual handling instructors available, if it is required. This means we can run courses simultaneously should the facilities be available to do so. The course information is based on the Manual Handling Operations Regulations 1992, amended 2002. It is also covered under the Health and Safety at Work Act 1974. At MHA Training we like to make our Manual Handling Training courses fun and use the best training aids available whilst also covering the serious points of the subject. MHA Training was established in 2008 based at our training centre in Warrington, Cheshire. We provide a wide range of services On-Site also for clients around the North West in areas such as Manchester, Liverpool, Widnes, St Helens, Runcorn, Wigan, Preston and Leeds. Over the years we have expanded and have instructors available for all of our courses Nationwide.

Are you, or your company in need of high quality first aid training? Do you require excellent training to fully support colleagues in the workplace? MHA Training Ltd would love to help with any of these requirements. MHA Training is approved by Qualsafe Awards, an Awarding Organisation recognised by Ofqual. This means we can offer regulated Qualifications in these courses. All of our courses are aimed to help employers to comply with the Health & Safety (First Aid) Regulations. First Aid Training is required by who? A knowledge of basic first aid can make the difference between life and death. Studies have shown that effective first aid can be vital in the first few minutes after an emergency. There are plenty of success stories in the media about this training saving lives as it’s such an important life skill. A first aid qualification can help your resume, CV, or even open up job opportunities. There may also be opportunities to volunteer using your first aid skills. It has been a vital life skill that people have used for members of their own family not just in the workplace. The 3 main goals are to preserve life, prevent worsening and promote recovery. You never know when the need will arise to put these skills to use. The First Aid Training experience. A First Aid training course should be an interactive fun learning experience, not all chalk and talk. This is achieved by using fully qualified trainers/assessors, who are very experienced “hands on” training professionals. Our trainers are sympathetic to the needs of the individual trainee and adept at getting the best possible standard from the delegates. First Aid At Work Regulations: In the event of injury or sudden illness, failure to provide first aid could result in a casualty’s death. The employer should ensure that an employee who is injured or taken ill at work receives immediate attention. HSE will prosecute in cases where there is a significant risk, a disregard for established standards or persistent poor compliance with the law. HSE First Aid at Work – IMPORTANT! After 1st October 2013 the HSE is no longer responsible for approving providers of First Aid at Work courses. Providers must be approved by an Ofqual or SQA Awarding Body. MHA Training Ltd fully meets all of the new requirements. MHA Training has been established for 15 years, based at our training centre in Warrington, Cheshire. We provide an array of services On-Site also for clients around the North West in areas such as Manchester, Liverpool, Widnes, St Helens, Runcorn, Wigan, Preston and Leeds. Over the years we have expanded and have instructors available Nationwide.

Our classroom training provides you the opportunity to interact with instructors and benefit from face-to-face instruction. For more queries, reach out to us: info@mangates.com

Our classroom training provides you the opportunity to interact with instructors and benefit from face-to-face instruction. For more queries, reach out to us: info@mangates.com

Our classroom training provides you the opportunity to interact with instructors and benefit from face-to-face instruction. For more queries, reach out to us: info@mangates.com

The aim of the course is to ensure that safety requirements are appreciated by managers. To enable them to review their own safety systems. It give’s the ability to introduce new controls and possibly implement changes as appropriate to ensure safety in the workplace. Who Should Attend? The course is designed for managers and supervisors in any sector, who are required to manage health and safety risk and resources within their organisation. It is also beneficial for anybody wishing to get into the Health and Safety profession or Management. The IOSH qualification is an impressive qualification to add to a CV. Course Duration: 3 days. Learning Objectives: On successful completion of the course, delegates should be able to: Explain ‘managing safely’. Explain the component parts of a recognised safety management system such as HSG65. Identify the data and techniques required to produce an adequate record of an incident. To demonstrate the procedure for an accident investigation, recognising the human factors involved. Describe statutory requirements for reporting and procedures for checking non-reporting. Describe methods of basic trend analysis for reactive monitoring data. Define ‘hazard’ and ‘risk’, and describe the legal requirements for risk assessment. Demonstrate a practical understanding of risk assessment technique and the data required for records. Describe workplace precaution hierarchies. Prepare and use active monitoring checklists. To implement schedules for active monitoring, recording results and analysing records. Outline the main provisions of the Health and Safety at Work etc Act and the Management of Health and Safety at Work Regulations. Outline relevant health and safety legislation, codes of practice, guidance notes and information sources such as the HSE. Syllabus: 1. Module 1 – Introduction and Overview. 2. Module 2 – Risk Assessment. 3. Module 3 – Risk Control. 4. Module 4 – Health and Safety Legislation. 5. Module 5 – Common Hazards. 6. Module 6 – Investigating Accidents and Incidents. 7. Module 7 – Measuring Performance. What do IOSH Managing Safely Courses involve? The course has seven comprehensive modules. These modules cover risk assessment and control, Health and Safety Legislation, common hazards, accident and incident investigation. Also covered is performance measurement. Effectively covering all aspects of safety management in the workplace. To obtain the IOSH Managing Safely certificate, attendees will need to complete a four day course. The course is delivered using high quality animated graphics. This includes sophisticated, fun presentations to make the content of the course more memorable. With training tools including board games, DVDs and quizzes displaying clear scenarios and essential practical content. We have worked hard to ensure that taking an IOSH Managing Safely course is as enjoyable as possible. Attendees will officially attain their IOSH Managing Safely certificate upon successful completion of both the written and practical assessments of the course. Certification: An IOSH Managing Safely certificate is awarded to all those who attend the course successfully completing both written and practical assessments. Candidates will also receive an excellent workbook from IOSH, with all the tools to help them once they are back in the workplace. Understanding of the course material is evaluated by means of a 45-minute written assessment paper consisting of 20 multi-format questions. There is also a practical assessment. MHA Training was established in 2008 based at our training centre in Warrington, Cheshire. We provide an array of services On-Site also for clients around the North West in areas such as Manchester, Liverpool, Widnes, St Helens, Runcorn, Wigan, Preston and Leeds. Over the years we have expanded and have instructors available for all of our courses Nationwide. IOSH Managing Safely Refresher Course: Recently IOSH have introduced a one day refresher course. This enables candidates having previously sat a course within 3 years to keep their qualification current and upto date in just a one day course. For more information please see the factsheet below.